|04-16-2009 06:44 PM|
|daanbc||Here's a pic of the spray, Blactoothgrin my engine is not as clean as yours-YET. LOL|
|04-16-2009 04:11 PM|
|daanbc||I use a spray & shine from honda. They make it for thier motorcycles. You don't need any water just a rag. You spray it on (foam) let it sit for about a minute then rub off. It leaves a wax like shine, it takes off grease/bugs/tar/ dirt. That's what i used to clean my fenderwells for the first time. They were loaded with road grime. I thought they were black untill i saw "blacktoothgrin's" pic's. Took me about 30-40 minutes to do both. The can cost about $8.00|
|04-16-2009 03:43 PM|
Well, it started off in pretty good shape from the guy that I bought it from.
As for me, I just use warm water/elbow grease/armor-all and some tlc.
I know there is some other nice and thick protective coating that can be put on it and let dry, right after you clean it. It's supposed to last for a few months at a time, but I don't know what it's called. Anyone know the name of that stuff?
|04-16-2009 12:25 PM|
|jdhallissey||I am in for the dirtiest engine I will get the thread started this afternoon!|
|04-16-2009 12:01 PM|
|4point||I try to keep mine clean but it don't look like that.|
|04-16-2009 12:00 PM|
|Jerry Bransford||We need a new "dirtiest engine compartment" thread for us others.|
|04-16-2009 11:54 AM|
|04-15-2009 09:31 PM|
And there's no shame in keep'n your Rig clean Dave.
At least, I FEEL NO SHAME...lol
Keep it up!
|04-15-2009 08:58 PM|
|04-15-2009 08:34 PM|
|innocent bystander||To heat shrink it will require cutting the wire downsteam somewhere. i would get the brush on insulator that 3M sells. That stuff works miracles.|
|04-15-2009 07:50 PM|
|04-15-2009 06:03 PM|
|jtalar||And Oh by the way....quit washing it!!!!!!|
|04-15-2009 05:53 PM|
|jdhallissey||you could even wrap them in electrical tape like you have then heat shrink it then rewarp those wires induvidually again. Then side the plastic tubing over it and tape that with water proof tape. It should not melt away again if it does then your looking into the relays being bad.|
|04-15-2009 05:03 PM|
|04-15-2009 04:57 PM|
|04-15-2009 04:57 PM|
|04-15-2009 04:52 PM|
|jdhallissey||Grab some heat shrink and waterpoof electrical tape and fix them. Then die-electric the connection again. It will be good as new after that.|
|04-15-2009 04:18 PM|
|GA_TJ||Yep. I'd second 4point on this. poor connection, too much juice through the circuit or my personal favorite, moisture. Sometimes you can get conductive liquids forming a path between two close connections. This can give you the short, and potentially enough juice to cook the coating.|
|04-15-2009 12:37 PM|
|4point||Insulation on automotive wiring has a higher heat resistance and is tougher to avoid chafing. I've seen many connections with the jacket burned back like that and its due to a poor connection and or over loading. Check the connector for more damage, if its gotten to hot the plastic connector around the pin will be burnt or deformed also. My guess is it was just a weak connection that caused it.|
|04-15-2009 12:00 PM|
|daanbc||What would cause this to happen? I've never seen insulation just deteriorate. Especially right by the connector.|
|04-15-2009 10:39 AM|
|04-15-2009 10:37 AM|
|daanbc||OK Guy's i found the problem, hope this helps out for some others. The other day i was cleaning my engine carpartment. So GA "TJ" got me thinking. I remembered i moved some wires by the headlights to clean underneath, WAHLAA i found the cause, both headlights have wires that have NO Insulation around them! Right at the connectors. I don't know what happened to them but they are bare. So when i moved them to clean i pressed two of them together causeing the short. I have pic's look where the screw-driver is pointed too. Thanks everybody!!!!!|
|04-15-2009 10:13 AM|
|daanbc||Not at all. The olny wiring i've done was with my fogs about 2-3 weeks ago. The headlights were working up untill last night.|
|04-15-2009 10:07 AM|
|GA_TJ||If the fuse is blowing, it's likely because there's a short somewhere in the wiring. You might follow the wiring from the lights to the fuse as much as possible, looking for burnt, worn, crossed, pinched, or otherwise look guilty. Have you done any wiring work under the hood recently?|
|04-15-2009 10:00 AM|
AAHHHG! Why is my IOD fuse keep blowing?
Ok, i went and bought a new fuse for my headlights. I put it in, turn the lights on and it instantly blows!!! I have not done or touched anything electronical or any wires. At $3.09 a fuse this is starting to cost me. What can cause it to blow? I see there have been other threads about this subject, but none state what was done to correct the problem. HELP! See my thread (Need help with FUSE? 30 AMP.) for pic's.