|12-11-2014 07:25 PM|
|AKS74||same boat, i have the rugged ridge bar, and just ordered a 20", hope it lines up easy for installation on the bottom.|
|10-28-2014 06:53 PM|
Does it bolt right on ?
What size is the light bar that you mounted on the bottom of the bumper bar. I just bought a 21 inch led bar. I was looking at this bar but not sure if it is a straight fit.
Goes out to itmeko3 I guess
|10-03-2014 10:22 PM|
|10-03-2014 09:54 PM|
|Jeepin granny||AACCCKKKKKK!!!!!! Thank you!!!! Thanks again to the forum, my question is answered!!!! Forum rocks!!!!|
|10-09-2013 06:59 PM|
|johngp7||just installed the rugged ridge light bar on my 2013 Wrangler Sport... no cutting needed|
|06-10-2013 04:30 PM|
I agree. If you add the stubby bumper kit it really freshens up the front quite a bit.
With or without lights, it's a good upgrade to the front until a new bumper is added.
|06-10-2013 02:43 PM|
|THW||I ordered one of these just for the look, without the lights! I think it's a great improvement in appearance over the look of the stock bumper, and for less than $100 it's an easy upgrade. Maybe I'll hang some lights from it eventually but I imagine I'll be upgrading the entire bumper before I actually need offroading lights...|
|06-10-2013 02:31 PM|
|That Jeep Guy||
Thanks for the info, Panthermark.
I'm really wanting a solution to affix driving lights before the long, dark winter arrives - the stock headlights are less than brilliant.
|06-10-2013 02:17 PM|
Olympic instructions (basically the same as well)
I don't know if they fit, but they don't really mess with the bumper itself, it is the trim piece behind the bumper that could give you an issue. Maybe you can take pics of the top and sides of your bumper.
The instructions provided are actually incorrect to an extent.
You don't need to remove to bumper or do any trimming. Just remove the air damn (6 easy to grip tabs) and use a long wrench with duct tape to hold the nut.
|06-10-2013 02:03 PM|
|That Jeep Guy||Are there any fellow EU jeepers here who know if this light bar works with our 'park bench' style front bumpers?|
|06-10-2013 12:20 PM|
But yeah, no cutting what so ever. A long wrench and duct tape made the install pretty quick and easy.
Not sure if I'm going to get a light or not. I wasn't planning on it because those flat LED's are EXPENSIVE. I'm thinking of cutting off the three mounts, that way, if I get into a slight wreck, they don't rotate back into my cooler/radiator.
|06-10-2013 11:58 AM|
I installed the Olympic one last year with no cutting. A little tight getting all the bolts aligned, but otherwise worked out nicely.
Just need to get lights...
|06-10-2013 10:59 AM|
That install was really, really, really easy.
|06-06-2013 01:49 PM|
|06-06-2013 01:49 PM|
As I read through the treads, some mentioned cutting the inner plastic, some said you didn't have to, others said it depends upon who made it.
I'm looking forward to putting it on...and I'm hoping this is not the start of some Jeep modding addiction.
|06-06-2013 01:45 PM|
|06-06-2013 01:34 PM|
While I doubt I add lights, I'm curious.
I just checked Amazon...my Rugged Ridge (Mopar) bar should be here today. I'm hoping it is the right version that will allow me to not have to cut anything. I also notcied the Olympic version is even cheaper....
|06-06-2013 01:12 PM|
|05-31-2013 06:35 PM|
Good to know the plastic does not have to be cut.
I think I'll go with this light bar (Rugged Ridge or Mopar...whichever I can find the cheapest) being that it can be had for under $100 shipped. Not sure if I should cut the tabs off, leave them empty or eventually install a flat LED light.
|03-31-2013 11:59 AM|
No need to cut a hole in the trim piece. The bracket goes around it in an L shape. It is a lot easier to install if you remove the air dam. The dam is very easy to remove just by snapping out 5 or 6 plastic inserts. Holding the nuts in place is the hardest part. I finally taped them to a short piece of a coat hanger using masking tape. Once the nut was on the bolt I could just pull the coat hanger out. Here is a picture of mine.
|03-30-2013 10:17 PM|
|03-30-2013 10:15 PM|
|ItsMeKO3||My plan is to mount an led bar upside down so its on the bottom of the bar. Between the bar and the bumper. Then mount 2 lights on the windshield like you have.|
|03-30-2013 10:10 PM|
|03-30-2013 10:09 PM|
|ItsMeKO3||Lol I know. My brother in law is a salesman there. Only reason its still on.|
|03-30-2013 10:08 PM|
|03-30-2013 10:07 PM|
|truthiness||Unless Blevins is a family member, kill that plate frame.|
|03-30-2013 10:05 PM|
Only one I have right now. Planning on putting an LED bar on it soon.
|03-30-2013 09:54 PM|
|03-30-2013 09:52 PM|
Anybody feel like posting a pic or two???
Much thanks in advance!!!
|03-30-2013 09:45 PM|
|ItsMeKO3||I almost made the same mistake 2 days ago when I put mine on. Then I went back and looked at the instructions once more and realized how it went. The brackets that mount to the frame are a huge pain in the ass though! I ended up using an allen wrench to hold the nut in place.|
|This thread has more than 30 replies. Click here to review the whole thread.|