Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > SYE setup

Join Wrangler Forum Today

Thread: SYE setup Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-11-2013 05:49 PM
Micky x2 on what Water Dog said regarding the Tom Wood's driveshaft. If you get them the measurements they usually have it shipped out by next day. It's pretty quick.

I went with the Currie relocation bracket and Currie trac bar. The bracket is the newer version that is angled away from the gas tank (JKS is angled as well). It is bolted on and requires a small weld on the housing tube. I know you said you don't have access to a welder and neither did I so I just called around and convinced a welder to come out to weld it for $25. It literally took him 5 minutes, and he was out of there.
Attachment 234888
04-11-2013 10:52 AM
Big Cole Take a look at tattons driveshaft service based in Utah. I paid $235 f
including shipping for my custom driveshaft. Its a quality unit and I have no complaints.
04-11-2013 10:25 AM
Water Dog I just did mine and went for the JKS bracket and adjustable trackbar. I figured since I was doing it, it would be nice to be able to get the rear centered. I used Tom Woods and was very satisfied. If you take a measurement from the rear seal of your transfer case to the center of the pinion yoke, measure your tc drop, and know what SYE you are using, you can call Tom Woods and they will do the math to get you the right length. You don't have to wait until you get it set up. Mine fit perfect.
04-11-2013 08:28 AM
homebrwd I just ordered the JKS bracket for mine as I am in the same situation. Should work with the stock bar.

Woods, Tatton, Carolina are all good shaft makers. Find out if you get anything like a good warranty, free lengthening/shortening and such from the local guy to see if its worth the extra costs.
04-11-2013 08:24 AM
SYE setup

Slowly I've been getting all my parts together to get rid of my t-case hanging low. Went with the currie aluminum rear upper and lower control arms. Have an Advance Adapters SYE kit on the way. Need some advise on the last two things I need.
For the drive shaft - should I go with a Wood's? I also have a local builder, but he's a little more.
I'm guessing once I get my pinion angle set, I'm going to need a rear trackbar relocation bracket. What is a good one to get? Would prefer bolt on, since I don't have access to a welder. Do I need an adjustable trackbar as well, or will stock do with the relocation bracket?
This is finally all coming together - can't wait to finish.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 10:04 PM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC