|10-15-2014 12:05 PM|
|09-25-2014 05:08 PM|
|GeorgiaTJ06||Dunno if this is a stupid question but where can I find if my jeep was manufactured in Cali, I have an 06 sport.|
|09-25-2014 05:02 PM|
I just had codes checked and got the P0132. This was after being on the highway at constant 65mph and the jeep basically died/stalled. I limped it to the side of the road and when flooring the throttle it ran but without WOT it would sputter and die. It starts fine and drives fine in the city. Auto Zone says it's likely the PCM; but I want to see if changing the O2 sensors first will clean it up. It also sometimes sputters a bit when accelerating when it's cold in the morning. Any insight?
|09-17-2014 07:57 PM|
|jase421||OK Newbie here, got my first Jeep this week. 03 Wrangler X with 59K miles and beautiful shape. Drove it home from Akron and ran like a champ for 2 hours. Wife got in for test drive and came back with engine light on. P0138 code. The only thing I did was check the fluids and air filter since the car is new to me, before she drove it. Thought I might have not put the filter back in correct, but didn't seem to be the case. Cleared the code by pulling battery cable, came on again after about 45 minutes driving. Thoughts? As when I test drove for a half hour before I purchased and for the 2 hours on the way home nothing. Anything obvious before I start switching out O2 sensors?|
|08-21-2014 06:29 PM|
Just replaced oxigen sensor, less than 24 hours ago, check engine light is on again
Sahara 2doors 2007, did I miss a step? What else could be wrong?
|05-08-2014 10:07 AM|
p0132 p0138 & P0121
Went through the answers. Still having problems.
The problem started with my 2000 TJ 4.0 (German model) running rough sometimes when warmed up.
Received p0138 and p0132. Replaces both O2 sensors by Bosch universal parts.
Problem still there. A mechanics in FL recommended to change the TPS. After I changed it I also got a P0121. First I thought the part might be broken. Changed it a second time P0121 still there. With the old TPS I still get P0138 and 0132 but no P0121.
The problem of running rough got worse with the new TPS.
Now we will go into the wiring. Any recommendations?
|09-26-2013 04:11 PM|
|csala027||Oh ok, well thank you , you saved me about 30 bucks. I can buy the part for 25 bucks and a guy said for 50 he can install it for me|
|09-26-2013 02:55 PM|
why what? the socket? it can be done with a 7/8 wrench and no need for it.
|09-26-2013 02:48 PM|
|csala027||May I ask why? Sorry I'm new, trying to learn everything I can.|
|09-26-2013 02:44 PM|
|Big Sarge||If only one is bad that is fine. you do not need the socket. I personally think they are a huge waste of money.|
|09-26-2013 02:42 PM|
It's 25 for the ntk brand do I need to buy a socket as well?
Also I can afford to install 1 o2 sensor and my jeep is a v6 is that ok? Or do I need to change our both sensors?
|09-26-2013 02:32 PM|
rockauto is the cheapest, price sounds off though!! Make sure that you use the NTK brand or you will experience problems. I have a thread that was moved to the general discussion area that has a discount code for rockauto.
|09-26-2013 02:29 PM|
|csala027||Know a cheap place to buy the part? Rock auto is 22 and AutoZone is 40.|
|09-26-2013 02:26 PM|
|09-26-2013 02:25 PM|
|csala027||is the o2 sensor bank 1 sensor 1 an upstream?|
|07-20-2013 01:04 PM|
|07-15-2013 03:45 PM|
|Under the Palms||
OK, been following these threads replaced my 02 sensor, bank on, sensor 2 per the PO138 code according to the diagram above. The Check engine light went out, it does seem to be running better, but still feels like running on 5.5 cylinders. This is a new 4.0 crate engine in a 2000 TJ. Without a CE light I'm not pulling any codes, so I'm wondering if it just needs miles to clear up, or how to find whats causing the continued problem
|06-23-2013 01:14 PM|
Ready to change downstram o2 sensor, but it's too tight 0.o
Hey thanks a lot for your helps guys, I changed my o2 sensor, just need the downstream one now.
|04-13-2013 03:12 PM|
|homiegx||I went and got the socket. Came off easy with it. Old one def looked spent.|
|04-13-2013 12:39 PM|
If you have heard of any that have bent, they were of incredible poor quality. It may be cheaper in the long run to buy a quality O2 sensor socket. If you damage the sensor you may need to being it to a shop so they can get it out for you. Plus if you have it and have another sensor crap out on you, you're set.
I'd let you borrow one of mine if you lived close by.
|04-13-2013 12:06 PM|
|homiegx||Yes bank 1 sensor 2 is one I'm trying to replace but the wrench won't slide on the sensor with the space that is available to turn the wrench between the skid plate and the muffler|
|04-13-2013 08:50 AM|
I went from the bottom. You were talking about downstream sensors right? Crawl under behind the front tire and look up and you can see both downstream sensors.
The one closest to you is Bank 2, Sensor 2. Closest to front bumper is bank 1, sensor 2.
I had to change bank 2 sensor 2. It was still tight. I could only get 1/4 turn at a time, if that, but eventually it came loose.
Haven't tried to get at bank 1 sensor 2 yet, but I would think go underneath in front of the front tire. It was more on the foreward side of the cat if I remember.
|04-13-2013 08:18 AM|
|04-12-2013 07:04 PM|
I ended up having to put an adjustable wrench on it. If you happen to have an open end that is the right size, this would be preferable to an adjustable.
Also you should be able to get a specialized wrench at autozone or something. It looks like a closed end wrench, but with a slot in the end so you can slide it over the wires.
Either way though, you might save yourself some trouble by spraying some break free on it first and letting it soak for a while before you try to unscrew it. Those things get seized up and take a lot of force to get them going, last thing you want to do is break it.
|04-12-2013 05:58 PM|
Please tell me,
-Were there any pre-failure signs?
-Were you getting more than 13 mpg
-What are you getting now?
-Did your fuel economy increase?
|04-12-2013 05:40 PM|
|homiegx||Ran into a little snag, how did y'all change the sensor after the cat? I can't seem to get the wrench to fit over the ridges on the sensor with the space that is given between the skid plate and the muffler?|
|04-10-2013 06:51 PM|
|homiegx||Thanks for info. Was about to just leave it over night from what I've read somewhere else|
|04-10-2013 06:50 PM|
|homiegx||Ok thank you|
|04-10-2013 06:49 PM|
|04-10-2013 12:11 PM|
|This thread has more than 30 replies. Click here to review the whole thread.|