Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > slave cylinder help...

Join Wrangler Forum Today

Thread: slave cylinder help... Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-15-2013 07:34 AM
rcac101 The lines steel, the bearing metal,plastic break away straps, my slave came as one piece
preassembled . All i did was slide it into place and tap a pin into the hole.After bleeding for 3 days i hooked up my vacuum pump and was good but since my stud mount broke, its the mounting thru bolt at the trany, ive had issues again...chk my clutch and mount post,...
04-14-2013 09:20 PM
joshmart613 The orings go on the two lines that pipe into the slave..when u got ur new slave cylinder, it should of had a baggie that had 4 orings, 1 roll pin, 4 u clips and a little lock nut to hold the cylinder in reuse the lines from the old cylinder and you put 2 orings on each end of the lines and put them in the slave and it is held in place with a clip...what kind of slave did you use, the plastic one or the aluminum one?
04-14-2013 09:02 PM
rcac101 Where exactly are these o rings i had one on my work pad didnt know where it came from. After i installed the slave in my GFs 90 wrangler
04-14-2013 09:02 PM
joshmart613 so are you guys saying that maybe Im sucking in air somewhere in the system and air may be blowing out the orings?
04-14-2013 08:54 PM
joshmart613 on the first slave cylinder i put in, i left the old master cylinder in...and it blew the oring...the second time i changed the master cylinder along with the slave cylinder, and it blew the o, bring the same im just scratching my head....i gotta think it has more to do with the slave cylinder hole bore where the hard lines pipe into them..i still have the aluminum one i couldnt get gonna compare the openings for the lines and check the oring housing seats sizes...if i could get the aluminum one primed, id be in business...maybe the orings supplied are too small, and get pushed out under pressure?....i dont know anymore, bout ready to pull my hair out...thanks for the input...i appreciate all the help i can get...
04-14-2013 08:46 PM
rcac101 Hey me too the new master on my GFs 90 wrangler was pulling in air i got another one, put it in removed the res, got a 11/4braided hose bushed it down to 1/4 in put an a/c svc port attached my 6cfm vacpump and wallah had clutch for 2 weeks. now new issue with clutch ....chk my other post
04-14-2013 08:31 PM
bajajohn your problem may be the clutch master cylinder. I had the same problem with the clutch on a Mazda I would bleed it and it would work good for a day or so then it would go to the floor I rebuilt the slave once and replaced it with a new one and it would bleed off.replaced the master and it's still working
04-14-2013 08:09 PM
joshmart613 Yea,its a one piece slave...and there arent any fittings to tighten the oringd in place...its just a u on the feed line and one for the bleeder line and its all held in place with a simple clip...i did submerge the aluminum slave in fluid and try to prime it by working it back and forth...but no such luck....couldnt get it to pump any fluid...submerged the plastic one and it pumped fluid over the edge of the im just at a loss...dont want to pull the tranny for a third time but i guess i will have too...just need to know how to solve my problem....thanks for the input....
04-14-2013 06:11 PM
0III0forlife If its a stock 87 then the slave cylinder and the throw out bearing are the all one piece style, and the only way I have got it to bleed properly is to reverse bleed the slave by pumping the slave back and forth to get the air out.

You might want to check and see if there is a burr on the end of the line that you are screwing into the fitting with the o-ring, maybe that is what is causing your mishap? Or it could be from over tightening the fitting itself, an o-ring fitting just has to be snugged down, not cranked down like a brake line fitting. The o-ring makes the seal, not the torque on the fitting.

I had the same problems with mine so often that i switched it all out for an AX15 with an external slave froma 97 TJ. Much better trans and much easier to work on as well.
04-14-2013 05:35 PM
slave cylinder help...

I have a 87 wrangler...stock straight six, stock tranny, stock everything....i had a slave cylinder leak, so i pulled the tranny and installed a new one, the plastic one to be exact...lasted about 2 weeks and it started leaking again (leak was on the oring on the feed side) i have pulled tranny and replaced, this time with the aluminum one...could not for the life of me get it to prime...the aluminum one didnt come with the, i ended up pulling the tranny AGAIN!!! and installed another plactic slave cylinder...was very careful to use clean hands, both orings, and made sure the orings set in the housing as to not damage them when i put the clips it all back together, bled system, drove round block, bled system again, drove around block, bled for the 3rd time and drove round block, everything was good as before...went in too a shower, got in the jeep to run an errand and the pedal went from good to flat...looked underneath and yep, it was leaking...leaking at the oring on the feed side again....what am i missing or doing wrong...why am i blowing out the oring on that side everytime....any help is greatly appreciated...

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 09:22 PM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC