Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > Builders Corner > Traction bars

Join Wrangler Forum Today


Thread: Traction bars Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-19-2013 01:37 PM
Square_Eyes There ya go :-) much cheaper then what i went with and you will get them without having to deal with the numbnuts at ballistics lol
04-19-2013 09:48 AM
Cons_Table
Quote:
Originally Posted by Square_Eyes View Post
The bushing i used is ballistics fab 2.63" weldable bushing they are $32 each
Bushed DOM Sleeve - RuffStuff Specialties
04-19-2013 09:44 AM
Cons_Table
Quote:
Originally Posted by Thriller View Post
Does your local shop ship cause I think that's a great price on the tabs. What size was those bushings. Again thanks for the help
If you cant get them to ship, check these guys out. Pretty reasonable prices on all kinds of fab stuff.

Off-Road Fabrication Parts - RuffStuff Specialties
04-19-2013 09:39 AM
Square_Eyes The bushing i used is ballistics fab 2.63" weldable bushing they are $32 each
04-19-2013 09:36 AM
Square_Eyes Im sure they would ill get you a phone number and the name of the guy I was working with and send you a pm
04-19-2013 09:31 AM
Thriller Does your local shop ship cause I think that's a great price on the tabs. What size was those bushings. Again thanks for the help
04-18-2013 10:29 PM
Square_Eyes The tabs i got from the local shop, he charged me $3 each, i got the creeper joints from that shop for $38 each. Got the bushings at ballisticsfab.com, wont order from them again but their product is great lol
04-18-2013 10:11 PM
Thriller Nice info been wanting to do this for sometime. Where did you order the brackets and joints ? Thanks for this helpful info
04-18-2013 05:53 PM
Square_Eyes I built some traction bars this week and decided to do a little write up on building mine since i had trouble finding a decent build thread on them to begin with. I went with a two bar design after speaking to a guy i met that owns a local shop, hes running a similar set up on his CJ with 40s and a super charged V8 with around 550HP so i figured after hearing about his experiance with the traditional ladder bar set up i would build the two bar set up.


Attachment 237776

I started by building a cross member so I didnt have to attach anything to the thin stock skid plate.
The bar is 2" square tubing that is 3/16" thick that measures 42"(outside of frame rail to frame rail), I cut the ends off at a 45° angle for aesthetics, welded the tabs 10" apart for a little bit of triangulation to help with articulation and then welded the bar in place. You could weld the bar to some plate and make it bolt on but I chose to weld it to the frame for simplicity.


Attachment 237781

I built the bars out of the same material as the cross member (2"x2"x3/16"), I cut the bars at 24 1/4" long (my rear axle is set back an inch so this measurement will vary).



Attachment 237782

I used creeper joints at the cross member side. I welded the large nut to the end of the tube and did not use a lock nut on the joint so that the bar can rotate when flexing the suspention. I made sure to take my end result measurements with the creeper joint exposing about 1/4"-1/2" of threads so i have some adjustment for more lift or moving the rear axle back further.



Attachment 237783

For the axle side of the tubes I cut out the ends to fit the bushing (balistics fab weldable bushing) using a jig saw with a metal cutting blade, its not presice and needs to be cleaned up with a grinder after words for a nice fit but it gets the job done when you dont have a notcher. Easiest way to get the right curvature is to place the end of the bushing on the tube and trace it with a sharpie.



Attachment 237786

After finishing both bars I installed the bushing guts and threaded in the creeper joint and bolted it on at the cross member, I bolted the tabs to the bushing end and held it up to the axle to figure out where it was going to go on the housing. Im running a ford 9" rear axle, so picking a place to weld the tabs was a bit easier since the whole housing is once piece and I didnt have to worry about welding to cast steel. Make sure when choosing a place to mount on the axle that it is below the center line of the axle, this will keep it from rotating upwords which is the whole point of adding traction bars. I then tac welded the tabs on and removed the bar and fully welded them in. I followed the same precedure for the other side.



Attachment 237788

After welding the tabs in and greased all the joints and bushings and bolted them in using 5/8"x 4.5" long bolts and nylock nuts.



Attachment 237794

Attachment 237795

Axle wrap was eliminated and as fst as I can tell flex wasnt hindered at all! Hope this helps and thanks for reading! If you have any questions post em up and ill answer as best as I can

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 03:49 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC