|04-23-2013 07:41 PM|
|tigerblood||thats highly likely, im sure you could find something to stick in there at the hardware store|
|04-23-2013 07:38 PM|
|Jimbo599||Hey guess what? No vent tube at all, just a big old hole. I guess that was where the problem started.|
|04-22-2013 04:46 PM|
|tigerblood||I glued my vent tube back in with black silicone after I realized how loose it was|
|04-21-2013 02:37 PM|
|indirocz28||yeah, I've had my vent tube come out of the housing before and not realize it. She got filled with water really quickly.|
|04-21-2013 01:14 PM|
|JD95YJ||make sure it all gets sealed back up good too. and make sure the vent tube is in place and not letting water in.|
|04-21-2013 11:33 AM|
Just take your time. If there weren't any shims, then you should re-install it as such. However, check your tolerances, and back lash. I can't remember if a D30 has a pinion crush sleeve or not, but you will want to replace that as well with a new one and torque your yoke nut back down and check back lash.
If you don't have a manual PM me and I can possibly get you a link to an online one.
|04-21-2013 08:22 AM|
|Jimbo599||I pulled the front end apart and found that the pinion bearing had come apart and was seizing up when rotated backward. The carrier bearings were bad as well. So new bearings and seals will go in this week. The gears look good so I can reuse them. There were no shims for the carrier, is that normal? Any tips on replacing the carrier and pinion?|
|04-15-2013 09:10 PM|
Wow that thing is toast. Clean with brake cleaner and hope the bearings arent toast from the moisture. Pinion looks possibly chewed as well. Personally I would get a new Dana 30 off CL for $150. That thing is a timebomb.
Check your rear asap.
|04-15-2013 06:00 PM|
|Jimbo599||Yes there is some moisture and some surface rust. The oil is more like mud. I'll pull the hubs off next and check them out. It will probably be a couple days before I can get to that. Thanks for the help so far.|
|04-15-2013 05:43 PM|
|rykemc||Might also check the left hub. If the carrier and gears look that bad I imagine that hub is pretty bad as well.|
|04-15-2013 05:33 PM|
|tigerblood||maybe its just the pic, but it almost looks like rust in there and alot of water moisture, and that fluid looks BAD, try to flush out as much of the old stuff as you can before refilling|
|04-15-2013 05:25 PM|
|Jimbo599||Pulled the diff cover and everything looks ok. It seamed like it might have been low on oil, only about a glass full, and what oil that was in there was pretty brown and watery. I just bought this jeep and I'm learning he wasn't very good at keeping up the maintenance.|
|04-15-2013 01:43 PM|
|OverkillYJ||and post a pic|
|04-15-2013 12:07 PM|
|SuperMidget||Pull the diff cover and i bet the problem will be easy to spot|
|04-15-2013 11:36 AM|
Dana 30 front end broken
I have a 93 YJ with a stock dana 30 front end, 4.11 gears and 33 tires. I was pulling out of my driveway and the front left tire locked up. Luckily it was on a dirt road and only about 10 MPH. I was able to roll the jeep forward but will not roll backwards. I was able to limp home by just creeping forward. Any ideas on what might be broke?