Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > Alignment after lift install

Join Wrangler Forum Today


Thread: Alignment after lift install Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-23-2013 09:55 PM
vankemp
Quote:
Originally Posted by crawlin_archer View Post
It's a solid axle vehicle, kinda hard to mess up camber when there isn't an adjustment for it. I have never messed with caster on any of the lifts I install. all you need to do is get your steering wheel recentered caue it will be off due to difference in the axle being lower then it was. This pulls the draglink to the right putting the steering wheel off to the right a 1/4 turn or less. If you use an adjustable trackbar you can adjust it yourself. All you do is measure the distance from the shock mount to the inside edge of tire. make sure you measure in the same spot on both sides. It's centered when you have the same measurement on each side. It's really simple.

And caster isn't something you really have to worry about normally on a solid axle vehicle. The reason is becasue it should be the same on both side. On IFS rides you can get different caster readings from right to left. And caster is what makes a car pull to one side or the other. A vehicle will pull to the side with the least amount of positive caster. But if your lift came with new control arms it should correct the result of losing some positive caster from the lift.

Thanks for the input.. I will dig into this tomorrow, but im quite certain he said the camber was showing out of whack by a decent margin -- I am going to a different dealer tomorrow to take another look.
04-23-2013 09:06 PM
crawlin_archer And to recenter the steerign wheel all you do is adjust the spanner on the draglink. On the 3" kits I do at work, it usually calls for about a half turn of the adjustable soanner.
04-23-2013 09:04 PM
crawlin_archer It's a solid axle vehicle, kinda hard to mess up camber when there isn't an adjustment for it. I have never messed with caster on any of the lifts I install. all you need to do is get your steering wheel recentered caue it will be off due to difference in the axle being lower then it was. This pulls the draglink to the right putting the steering wheel off to the right a 1/4 turn or less. If you use an adjustable trackbar you can adjust it yourself. All you do is measure the distance from the shock mount to the inside edge of tire. make sure you measure in the same spot on both sides. It's centered when you have the same measurement on each side. It's really simple.

And caster isn't something you really have to worry about normally on a solid axle vehicle. The reason is becasue it should be the same on both side. On IFS rides you can get different caster readings from right to left. And caster is what makes a car pull to one side or the other. A vehicle will pull to the side with the least amount of positive caster. But if your lift came with new control arms it should correct the result of losing some positive caster from the lift.
04-23-2013 08:50 PM
vankemp
Alignment after lift install

Just wondering if anyone has had any alignment issues after installing their lift --

I want to be careful not to wear my tires on the inside if the camber is off. I talked to my installer of the lift kit, and he says there should be no issues with the camber because it is a straight axle, and the lift should not be an issue.

I put a 4" (readylift) lift on, and I just took it down to have it aligned and they said I will need Cam adjusters to get it right.. Quote was $394 installed..

I went to Readylift site and did find this..

Installing a lift kit on any solid axle vehicle will alter the position of the axle. This can be corrected with the addition of an adjustable track bar available through most off-road parts dealers, check with your local dealer for options in your area. If you have any questions please contact our ReadyLIFT customer service department.

So -- back to my question.. what to install (if anything) to insure everything is aligned properly, or what have others done??

Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:26 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC