|04-26-2013 06:53 PM|
|NFRs2000NYC||Yea, without tuning your antenna, you're just shooting blind.|
|04-26-2013 06:49 PM|
|robdizzle||I know the coax isn't pinched as I took extra time and effort to lay it out nicely. Wasn't aware of testing the swr till I got to work. I work 2nd so now im at work and all i can think about is getting the heck out of here. Only about 5 hours left tick tick|
|04-26-2013 06:44 PM|
|04-26-2013 06:18 PM|
|robdizzle||I did not specifically run a ground from the antenna to a spot on the frame. I was under the assumption that as long as I bolted the antenna mount to the back door of the jeep it would be fine. Guess this it what happens when you assume|
|04-26-2013 05:58 PM|
|NFRs2000NYC||Did you ground the antenna? If you did, post a pic of it up close.|
|04-26-2013 05:44 PM|
|04-26-2013 05:31 PM|
1) Run a ground wire from the antenna mount thru the tailgate to the body.
2) Tune your antenna with an SWR meter.
|04-26-2013 04:28 PM|
|robdizzle||There were 2 times I heard some bits of conversation come through but then that was it.|
|04-26-2013 04:17 PM|
|jeepers29||I had the same problem. I tried to mount my antenna to 2 different locations on bumper and tire carrier. Niether worked. Ended up going with a Teraflex tail light mount and all was good. I guess I was not getting a good ground thru the bumper.|
|04-26-2013 03:45 PM|
|04-26-2013 03:37 PM|
|Senior Chief||If your SWR is way off you'll blow a final-output transistor. If there's a reputable CB shop close by they'll check your SWR for a small fee.|
|04-26-2013 03:30 PM|
|robdizzle||Yes I did assume that. Would a ground wire from the antenna to my steel xhd rear bumper do the same or no?|
|04-26-2013 03:21 PM|
|Silverton34||You are counting on the tailgate being properly grounded through the hinges. Try a temporary ground wire from the antenna to the engine block, that would rule out the ground issue.|
|04-26-2013 03:18 PM|
|robdizzle||I ground the paint off where I connected the antenna and reused a factory bolt on the tailgate when I retightened it. Maybe I need try something different. Now I'll just be thinking about it all night long while at work.|
|04-26-2013 03:07 PM|
|04-26-2013 03:05 PM|
|robdizzle||I appreciate the help.|
|04-26-2013 03:00 PM|
No worries. SWR-The SWR meter or VSWR (voltage standing wave ratio) meter measures the standing wave ratio in a transmission line. The meter can be used to indicate the degree of mismatch between a transmission line and its load (usually a radio antenna), or evaluate the effectiveness of impedance matching efforts.
You might be able to borrow one or Radio shack sell them for $40. The bars show you have power not necessarily signal. Check you have a good ground and wire didn't kink or get broken.
|04-26-2013 02:50 PM|
|robdizzle||New to installing CB's so pardon my ignorance|
|04-26-2013 02:47 PM|
|robdizzle||I went through all connections and they are good. Brand new coax because I broke the end off my first one. Not sure how to test the swr meter just yet. Need to reread the manual but when I depress the mic switch I've got bars all the way across|
|04-26-2013 02:39 PM|
|Sinister6||If you STILL have power ie didn't blow fuse somewhere... Connections tight? Bad coax? What readings you getting through SWR Meter?|
|04-26-2013 02:27 PM|
cb frustration. ideas??
I just installed a new cobra DX lV cb. Powers on, ran a p.a system into the engine bay. That works. I have zero communications through any of the channels. Routed all coax cable under the roll bar covers and mounted to the back door with aluminum mounting tab. Maybe my ground isn't good enough???