|04-30-2013 12:27 PM|
|04-30-2013 12:22 PM|
|04-28-2013 03:10 AM|
|BlackTJ94||Thanks guys you fixed the problem!|
|04-27-2013 11:38 PM|
For the 4lo problem you need to install the drop bracket that should have came with the kit and you'll need to adjust the linkage using the adjustment bolt on the back side of the linkage, close to the floorboard.
|04-27-2013 11:27 PM|
I had to remove the plastic piece that the hose connects to on the rear fender and reach inside to move the bottom of the hose then did the top. PITA too.
On the 4lo issue shift into 4lo inside the cab. ( have someone hold it in place ) With the nut on the adjustment arm loose move the tcase shifter arm firmly into 4lo then slide the adj rod foreward. I had to use a small ball pin hammer to tap the adj rod forward then tighten the nut back down. I put too much on the first time and she wouldn't stay in 2hi so I backed it off a little and its perfect.
|04-27-2013 09:43 PM|
|Nutsz71||Didn't have any hose or line problems with my 3.25 lift|
|04-27-2013 04:47 PM|
|BlackTJ94||Also my fuel filler hose is about an inch too short. How did you all deal with that? Did you just loosen the hose on each end and make some room?|
|04-27-2013 08:11 AM|
|chuck_D||I had the same problem with my shifter after I installed my 4" lift. It would not go into 2nd, 4th, 6th, or reverse. My problem was the shifter was hitting on the shift boot and the little trim piece that holds the boot to the consol. After I removed that it would still pop out of 2nd and after some looking it was hitting the plastic piece that covers the shifter hole in the floor. So I ended up just notching it and now no problems. I realize its not the best method but it works until I can do a SYE. Hope this helps the OP.|
|04-26-2013 10:10 PM|
|Nutsz71||I had the same problems. As far as the 4lo issue I had to flip the little bracket upside down to change the angle enough to move the linkage forward. As far as the trans shifting the same options were given to me of remove the foam, move the console backward, bend the shifter, or install a SYE. When I removed my boat there was no foam so that wasn't a fix. The SYE is about $500 with driveshaft and I just don't have the $$$ for that. I chose to bend my shifter. I took the shifter off, removed the knob, put it in a vise and beat the piss out of it. I did have to bend it two ways, once up to keep it off the bottom and then again at the upper bend back down to get it out of the dash. It was very easy and would be hard to screw it up and it works like it did before I installed the lift. Hope this helps!|
|04-26-2013 09:24 PM|
|Water Dog||Senior Moment...!|
|04-26-2013 08:57 PM|
|jasongind||I only addressed the transfer case linkage as that's all I had knowledge on. I wasn't going to make suggestions on something I didn't know about, I knew someone on here had the knowledge to address it.|
|04-26-2013 07:14 PM|
The op is talking about not being able to get the transmission into 2nd, 4th, and reverse, and all the answers are refering to the transfercase linkage.
Pull the boot up and see if the shift lever is hitting the body. If it isn't, simply remove the foam cover that surrounds the shift lever (under the boot) and try it again.
|04-26-2013 05:54 PM|
|04-26-2013 05:44 PM|
|04-26-2013 05:08 PM|
|jasongind||NP, good luck. Its an easy 5 min install.|
|04-26-2013 04:50 PM|
|04-26-2013 04:44 PM|
|jasongind||Nope, as far as I know the mml is used to correct drive line angle that may cause vibration. I have a M.O.R.E. mml but that was for use with the belly up kit.|
|04-26-2013 04:36 PM|
|04-26-2013 04:34 PM|
The piss poor design of the factory linkage is the problem.
The Novak cable shifter is the answer. Quality product, easy install no more issues.
|04-26-2013 04:30 PM|
Yup, with that much of a BL you need to extend or adjust the linkage. The BL kit should have come with a piece to extende the linkage if you can't get it adjusted.
If you get under your Jeep you can see the linkage. It is an easy 10mm, IIRC, nut that you losen then slide a rod back and forth to shorten or lenthen the linkage.
|04-26-2013 04:20 PM|
Having 4 Lo problems!
I just Installed a 1.25 inch body lift and a 1 inch mml on my wrangler that has a 2 inch lift. I'm having trouble putting it in 2nd, 4th and reverse. It will go in but It's really tight. In addiction to that I can put it in 4lo but it won't stay there it pops right out when I start moving. Any reason as to why this is happening??