Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Deleting Evap system

Join Wrangler Forum Today


Thread: Deleting Evap system Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-28-2013 06:35 PM
JellisTJ
Quote:
Originally Posted by Hardermods View Post
Did you physically see a spot on the rusty line that is opened? Have you checked the hoses at the purge valve? They are notorious for cracking a cause these Evap codes. And they are really simple to replace.

Examples:
exactly where mine are rotten.
04-24-2013 12:27 PM
nuclearmuscle523 Its a 3v. 2v motors are just.... dinosaurs.
Ill try to find a way to cheaply run the line. Just the level of rust alone screams that it is guilty.
04-21-2013 03:21 PM
jgorm
Quote:
Originally Posted by nuclearmuscle523 View Post
I was also thinking of plugging the check feed so that it "thinks" its holding pressure. Idk.
That wont work, its a dynamic system. sucks on the mod motor. 1000hp is damn good on any mod motor, especially if its a 2 or 3v!
04-21-2013 12:11 PM
nuclearmuscle523 I've spent time checking over most of the hoses. It gets quite rusty where you can see it by taking out the drivers side drain plug for the bench seat. I was also thinking of plugging the check feed so that it "thinks" its holding pressure. Idk. I delete nearly everything on my cars so that when something goes wrong, its something serious. That's coming from the 1,000hp modular ford I just made a coffee table out of. Sigh....
04-21-2013 11:45 AM
Hardermods Did you physically see a spot on the rusty line that is opened? Have you checked the hoses at the purge valve? They are notorious for cracking a cause these Evap codes. And they are really simple to replace.

Examples:
04-21-2013 11:14 AM
TCogley instead of spending money on kits or removing evap which as jgorm said is a waste of time and no company makes, why not spend 100 bucks on getting 1hr diag from a dealership, just because the line is rusty doesn't mean its the problem, it could be as simple as a control valve, or a gas cap that is leaking, as a mechanic i spend lots of time diagnosing evap leaks....id recommend spending 100 on getting it checked it before doing anything drastic
04-21-2013 10:32 AM
jgorm It's not trivial to bypass the evap system. There are multiple checks. It pulls vacuum, closes the valve, and looks for a leaks by monitoring the pressure. It's very sensitive and can pick up leaks similar to 1psi / hr. When it opens the valve it must see a change in the fuel trims that indicates that its burning the fuel vapors. If you have smog to deal with, your best bet is to fix the system. You can run a new tube to the back if that is the issue. Check your gas cap too. Smog law are serious. No company will make a delete kit. Edge performance got fined $500K for making DPFE delete kits for diesel trucks. Individual fines can be $10K and shop fines can be $50K+.
04-20-2013 11:17 PM
nuclearmuscle523
Deleting Evap system

I have the p0455 code evap large leak
I have emissions soon and with a rusty evap line running the length of the car, I feel like ripping the whole system out. I like things being more.... simple. Less that can go wrong.
What value resistors must I solder in what locations to make this thing throw no codes. Or what resistor can I at least use to make the p0455 go away?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:26 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC