Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > 33x12.50 do i need to switch gears ?

Join Wrangler Forum Today

Thread: 33x12.50 do i need to switch gears ? Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-29-2013 03:27 PM
Originally Posted by Robert C. View Post
Sweet thanks for the info how much does that run ? And ill look at see what it says.

I just had mine changed out from 3.07 to 4.56. I have 33's and the 4.0. I never knew that the gear swap could make so much difference. I absolutely love it. It feels like I've added 100 hp to the engine. It was fun to drive before, but now, wow! Should have done this a long time ago. My cost was around 1800.00, but my old gears were worn out along with the axles, bearings, spiders, so I got the open differential replaced with a LS diff.
04-29-2013 10:52 AM
Robert C. Oh ok ill look it up and it might be possible that it is slightly less on rpms i checked again on the way to work and at 60 its just touching 2 grand so idk if its less ir not
04-29-2013 10:36 AM
Jerry Bransford
Originally Posted by Robert C. View Post
2000Rpm at 60 mph in 5th gear ?
That calculated out to a 4.10 ratio. A good online calculator is at though it doesn't have all the TJ's possible transmissions.
04-29-2013 09:02 AM
Robert C. Ya ill upgrade to the new gears i need to find a shop and a price. 35s are in mind soon... thanks
04-29-2013 02:50 AM
Rob and TJ I have 3.73's on 33" and @ 60mph your at the same rpms I am. I have a HUGE dilemma in that, I just bought a 2013 Polaris rzr..its weighs 1000lbs dry and my trailer weighs 700...sooo im working my tranny way way way to hard. After looking on here and talking to a local six states driveline shop, im going to 4.56's. It'll increase my highway ability to keep speed without downshifting every small hill in encounter..towing or not. Also, my gas mileage should improve..will improve with towing. Also, 4:56's give me the ability to go to 35's a little more comfortably and only sacrifice about a 200 rpms difference vs the 600-800 im sacrificing now. A REAL good driveline shop should quote you about $2000-2500. 2500 if they have to change every bearing and seal with the axles itself. I was quoted about 16 hours labor and the rest in parts...they are going factory Dana gears. I was quoted all sorts of prices from a bunch of shops. And yea, I was sticker shocked. But as I have never done gears myself and know I don't have the proper tools to fix handle the lash adjustments and whatnot I feel more comfortable having pro's do it and warranty it. But that's just me! GL keep us posted!
04-29-2013 01:01 AM
Robert C. Ya i think its been changed i went through The speed cameras going five over and it didn't go off and several other school zone radar its right on. So i need 4:56 for it, it looks like $200 or so for the gears and a sat to change them out. Thank ya'll
04-29-2013 12:53 AM
Hamster If your GPS is showing 60mph in 5th gear and your engine is turning 2000 rpm, looks like 3.73 gears. Don't trust the vehicle speedometer if they didn't change the speedo gear.
04-28-2013 11:33 PM
Robert C. 2000Rpm at 60 mph in 5th gear ?
04-28-2013 09:54 PM
1jeeplvr I did 4.56 gears in my 5sp,4.0 & at 65mph Im at 2500rpm
04-28-2013 09:29 PM
Jerry Bransford You need to spin a rear tire precisely two revolutions for the differential to rotate the rear driveshaft the number of times that equals the axle ratio.

If you have a GPS, tell me what your engine RPMs are at 60 mph per the GPS in 5th gear & I can tell you your axle ratio.
04-28-2013 07:25 PM
PStov98TJ So as already said, because its a 4.0, you've either got 3.07 or 3.73's most likely. It's possible you have 4.10's though. It was an option for a few years.
04-28-2013 07:07 PM
Robert C. Cool ill do that tonight and its a 4.0
04-28-2013 07:02 PM
PStov98TJ This is how you can for sure tell and take the guess work out. Jack the rear tires off the ground enough they can freely rotate. Get under the jeep and turn the drive shaft. Count how many drive shaft rotations it takes for one rotation of the tires. (Note: if only one wheel spins, then count the number of DS rotations for two full rotations if the tire). If it spins about 3 times, you've got 3.07's. If it spins just under 4, you've got 3.73's. If it spins right at/just over 4 turns, you've got 4.10's. About 4.5 turns is 4.56's. And just under 5 turns would indicate 4.88's.

Just curious, you have the the 4.0L or the 2.5L? That'll help narrow it down a bit.
04-28-2013 07:01 PM
Robert C. Sweet thanks for the info how much does that run ? And ill look at see what it says.
04-28-2013 06:58 PM
Water Dog It sounds like your differentials probably have stock gears of either 3:07's or 3:73's. There should be a metal tag on the rear end that says what the ratio is. With a 4.0 5 speed with 33" tires, the optimum gear ratio would be 4:56, which means a regear would be a good thing to pursue.
04-28-2013 06:39 PM
Robert C. Well going through the intersection. I shift at 2 or less on the rpms but its almost all the way through. In the wind in fifth its not too bad but its no race car. I know the transfer case was redone or regeared in 08 i have a 99 tj 4.0 manual. On the back of the transfer case it had a circle plate with stamped numbers m/d/y nd it was in 08 so idk
04-28-2013 06:32 PM
jp2611 I have the same set up however I was the one who did the switch.....things that tell you that you need to regear.........
1) Speedo doesn't match GPS!!
2) When taking off from a light in first gear, it is possible to get all the way through the light and still be in first gear whithout the motor screaming at you.
3) When shifting from 4th to 5th and merging with traffic on the highway your jeep slows down.
4) and Lastly...your Jeep doesn't really feel like it is running right unless you are running 70 or better on flat ground with a tail wind...feels as if no power in 5th gear.
04-28-2013 06:14 PM
Robert C.
33x12.50 do i need to switch gears ?

I have 33x12.50 on 15 inch rims. I dont know if they had the gears changed the jeep is new to me. What would indicate if they have been changed ? Or do i have to take the plate off the pumpkin? ? Would the 33's make 5th gear sluggish ??

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 09:01 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC