Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > installed SYE wont come out of 4low

Join Wrangler Forum Today


Thread: installed SYE wont come out of 4low Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-01-2013 05:46 PM
TeraFlex If you have any more issues, please give us a call. 1-888-837-2359 ext 318 is Doug our t-case expert.
05-01-2013 04:38 PM
Jaminjer I finally got this all back together, tried to drive it a few feet and still would not come out of 4 hi. I figured I had put something back together wrong so started taking some things loose and when I tried to pry off one of the linkage arms it moved, jumped in jeep and was able to take out of 4 wheel drive. Found out my linkage had bound up somehow, lubed all the linkage points now good to go. Ordered rear drive shaft so only have one in front, drove to work that way, no problems.
04-29-2013 08:12 PM
jeepers29 what issues are you having with gear changes? I have not seen anything about issues like that? My shaft and Teraflex kit came today, so wanting to get started tomorrow. Thanks guys.
04-29-2013 08:09 AM
Water Dog
Quote:
Originally Posted by Jaminjer View Post
Good snap ring pliers are a must!!! I tried my wimppy ones originally, finally oreilly had some good ones.
If I were to do it again i think i might pull the whole transfer case. The worst was the oil pickup flange or what ever you call it, making sure it was right. After I had it installed I found a good youtube from advanced adapters I did leave the transfer case in as most have advised.
Jeep is on ramps, will have to take it down tomorrow and see if i can rock it and get it out of gear.
I also watched that video...pretty helpful. I didn't have any issues with gear changes, but mine was on 4 jackstands under the axles.
04-28-2013 11:41 PM
Jaminjer Good snap ring pliers are a must!!! I tried my wimppy ones originally, finally oreilly had some good ones.
If I were to do it again i think i might pull the whole transfer case. The worst was the oil pickup flange or what ever you call it, making sure it was right. After I had it installed I found a good youtube from advanced adapters Jeep New Process 231- NP231 SYE Install - Slip Yoke Eliminator - YouTube.
I did leave the transfer case in as most have advised.
Jeep is on ramps, will have to take it down tomorrow and see if i can rock it and get it out of gear.
04-28-2013 11:00 PM
jeepers29 Thanks water dog.
04-28-2013 10:41 PM
Water Dog
Quote:
Originally Posted by jeepers29 View Post
Jaminjer, not to hijack, but I am doing this install on Tuesday. Any tips? I was planning on leaving the trans case in the jeep. What did you do? Thanks
I'm not him, but I installed mine about a month ago while it was in the Jeep, and if I had to do it again, I would do it the same way. If you have a nice creeper with a head rest, it's a piece of cake. Hardest part was the large snap ring in the output shaft housing, but If the thing was laying on the bench unrestrained, it probably wouldn't have been any better. Even with really good snap ring pliers, they kept wanting to slip off. Wound up having to get a couple of screw drivers in behind it.
04-28-2013 06:56 PM
jeepers29 Jaminjer, not to hijack, but I am doing this install on Tuesday. Any tips? I was planning on leaving the trans case in the jeep. What did you do? Thanks
04-28-2013 06:04 PM
PStov98TJ It helps to be moving at about 2-3 mph to move into/out of 4lo sometimes.
04-28-2013 05:26 PM
Herbie424 Usually have to be in neutral to get into or out of 4lo and sometimes even crawling forward babysteps
04-28-2013 02:57 PM
Jaminjer
installed SYE wont come out of 4low

I just installed teraflex SYE into my 231 transfer case. I am pretty sure I got it all together correctly. Should I be able to take it out of 4low without starting it?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:21 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC