|08-27-2013 09:42 AM|
|YJ fanatic||WeekenderATX, don't waste your money on the D35. Save the money and buy an 8.8 with limited slip for ~$200. The swap is easy, and its a way better axle.|
|08-27-2013 09:33 AM|
|WeekenderATX||Aussie in front is sounding better and better. For my D35 rear, I'm leaning toward LSD (maybe Eaton Detroit TrueTrac), rather than locker, for on-road manners.|
|08-26-2013 09:14 PM|
|brachilius||I ran Detroit ez lockers in my 91 2.5l. The rear ez locker was done in about 18 months. I rounded off the teeth. I replaced it with a lock rite. It lasted for years. It was in a Dana 35. I live in PA and we get some good snows. I never had any trouble. I would just drive cautiously. If you have the money, get a selectable rear locker. To do it once...swap in an 8.8. It is a waste of money to buy an ard or elocker for the 35. I have about $750 into my 8.8 swap. That's a 4.10 axle, ruff stuff install kit, auburn elocker and install kit. Total swap cost will be $850 once I buy the ebrake cables and ujoint flange. That is less than an arb for a 35. I did not include brake parts in the expense as my 8.8 had good brakes.|
|08-26-2013 08:54 PM|
Yes, I still have the stock axle and vacuum system. The short left shaft still spins, which will spin the gears and since its locked, it will spin the driveshaft. This shouldn't create any problems though. YJ front shafts aren't balanced from the factory, but most of them I've seen are good enough and don't cause vibrations.
My only problem was that I bent my driveshaft last year, so I went and bought a YJ shaft that someone had balanced.
|08-26-2013 07:56 PM|
The reason I ask is I have a Lock-Rite in my stock front axle, which like you said off road its awesome, and although while in 2H the split axle disengages, it still makes the front drive shaft spin and thus creating heat and drag, this is the new normal right?
|08-26-2013 07:17 PM|
|YJ fanatic||Yup, its in the front. Totally invisible in 2wd. I've never heard it click or pop, but you know its there in 4wd. It works very well.|
|08-26-2013 06:20 PM|
|WeekenderATX||You have it in the front? Is it invisible when not in 4WD?|
|08-26-2013 04:09 PM|
|YJ fanatic||Check out Aussie. I got mine for like $250 and it works great.|
|08-26-2013 01:45 PM|
Started pricing today.
For my 27 spline front Dana 30, pricing for the Powertrax No-Slip (Part # PTX9204302700) is right around $450.
Ouch. That's a lot more than I thought.
I've read several reviews that say it's 99% invisible in the front, though.
|06-24-2013 10:35 AM|
|WeekenderATX||Thanks for the ongoing insights, everyone. Keep 'em coming.|
|06-24-2013 10:09 AM|
If your on a budget and can't throw money at your rig, then a lunch box locker in the rear on a D35 will work and make your jeep more trail worthy, that is a fact, I did it for over 10 years no breakage, and a bunch of trips to Moab, for trails like poison spider, hells revenge etc...
Now if your planning to throw 38" tires on and go full throttle to get up a hill or when you get stuck, your going to break things...IMHO anyway...
|06-24-2013 09:56 AM|
|06-24-2013 08:05 AM|
The locked front is nice, and awesome offroad, but I try to avoid turning the wheel all the way on pavemwnt. That isnt always possible for me since I live in the city. It still bangs pretty loudly making tighter turns up front on pavment, and sometimes coming out of a turn hitting the gas it pulls to one side for a second. It also might have to do with the fact I swapped in a solid axle to gain the benefit of the greasable outer seals. I wish the front performed as well as the rear. I will just need to get a selectable locker up front eventually. For now it does everything I want it to though.
One thing to note though is that in snow LSD and a locked front are not good at all. Good way to wreck. With a selectable being able to drive in 4WD with open diffs is the best, at least where I live. If you go sideways here you will hit something or get hit by something.
|06-23-2013 09:56 PM|
P.S. Actually "perfect" would be a selectable front and rear like ARB if you have the money to throw at it.....I don't
|06-23-2013 02:15 PM|
|06-23-2013 01:49 PM|
One glitch in this is if you are starting from an "open diff" axle, meaning that there is no LSD in it.....If you have a LSD in the axle then you can't just take out the LSD and install a Loc-Right/Spartan/Aussie etc...
|05-15-2013 04:37 PM|
|jeremyx28||What else should I buy and have on hand when I go to do this job? Seals and gaskets and whatnot|
|05-15-2013 04:23 PM|
|05-15-2013 03:59 PM|
|OverkillYJ||Depending on your particular jeep you may have to pull the ring gear off the carrier. I had to do it on mine when I installed my Spartan.|
|05-15-2013 03:47 PM|
|05-15-2013 03:09 PM|
|jeremyx28||Rustysoffroad has the lock right for the Dana 30 for $210 plus $20 shipping. I can't find anywhere else that can touch this price. Do you think at that price its the way to go?|
|05-11-2013 11:26 PM|
|Ditchdoc||Sorry that was a question.|
|05-11-2013 09:23 PM|
|Ditchdoc||Tell you what I could have used them today.|
|05-09-2013 07:13 PM|
|GoldenSahara00||Biggest issues I had with mine were getting the shafts out because they had been in there so long, and the fact that the bolt holding my cross pin in broke...|
|05-09-2013 07:12 PM|
|YJ fanatic||It's fairly easy. It took me and 2 friends 2.5 hours to do it, and we replaced the u-joints too. Any questions, just ask.|
|05-09-2013 07:08 PM|
|GoldenSahara00||No c clips. We're here if you run into trouble. I did mine and taught myself. follow directions, read them a few times before you jump in.|
|05-09-2013 06:50 PM|
I wish I knew some local jeepers, or someone who could supervise/help with the job. I can follow directions and I read that the spartan comes with very detailed instructions. It shouldn't be too hard. Thanks again everyone for the help.
BTW, its a 95
|05-09-2013 06:46 PM|
My 92 YJ did not have c-clips. Didn't even have the channel on the shaft for one. But I would say that pulling the axles and carrier would be 100x easier than trying to get everything positioned with them all still in.
Also, the test does work in 2wd. Mine does at least.
|05-09-2013 06:43 PM|
|GoldenSahara00||I edited my last post a little. From my knowledge what I told you is correct. Try it in 2wd. If only 1 tire turns, then you need 4wd This is for the front. As far as the install, I would take the carrier out, it's just easier.|
|05-09-2013 06:38 PM|
|jeremyx28||Thanks anyway, maybe someone will come along with the answer. I'm gonna get my Google on and see what I can find out.|
|This thread has more than 30 replies. Click here to review the whole thread.|