Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Pinion shaft

Join Wrangler Forum Today


Thread: Pinion shaft Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-12-2013 09:05 PM
Dfishman76 The outer pinion bearing was bad. Had to,change it out.
05-04-2013 01:26 PM
Jerry Bransford Spell check must have got me.
05-04-2013 12:26 PM
tangofox007
Quote:
Originally Posted by Jerry Bransford View Post
Replacing a pinion bear bearing is not difficult...
A pinion bear?

That would have to be a bear of a job!!!
05-04-2013 12:24 PM
tangofox007
Quote:
Originally Posted by Dfishman76 View Post
Got it fixed and was not that bad. Thanks for the help
What, exactly, did you do to solve the problem?
05-04-2013 11:31 AM
Dfishman76 Got it fixed and was not that bad. Thanks for the help
04-27-2013 12:20 PM
Jerry Bransford
Quote:
Originally Posted by Dfishman76 View Post
Looks like the pinion bearing is bad how hard is that to change?
Replacing a pinion bear bearing is not difficult but neither is it an easy job. You would need a bearing puller and press, and you'd have to mostly disassemble the axle by sliding the axle shafts out & removing the carrier to get at the pinion gear. Then you'd have to know how to arrive at the proper shim thickness via a little math so the pinion gear would be at the correct depth again after pressing the new bearing onto it.

If you have access to a bearing puller & press, it's not a difficult job but it's not one that many Jeepers here would be up to.
04-27-2013 09:45 AM
Dfishman76 This is the front pinion. Bearing should have not play in it at all right? How bad is it to change? This one has play in the bearing.
04-27-2013 09:32 AM
Patrick H Could be bad pinion bearings, or the pinion nut may just be loose. They don't usually loosen up unless there has been work done on the rear end (pinion seal replacement, etc.) or the bearings are bad.
04-27-2013 09:29 AM
Dfishman76 So what could be causing the play? Gears look good.
04-27-2013 09:22 AM
Patrick H There should be *zero* lateral or longitudinal play.
04-27-2013 09:13 AM
Dfishman76 How much movement should there be on the pinion shaft? Is it ok that it moves any at all? Should it move in and out any? I have a little play in mine up and down and moves a little in and out is this normal?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:33 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC