Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > 97 TJ Clutch/Tranny Whine

Join Wrangler Forum Today


Thread: 97 TJ Clutch/Tranny Whine Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-10-2013 09:17 AM
Water Dog If it's driving okay, and is just having throw out bearing noise, I would drive it. Worse that could happen is the T-O bearing gives out and you have to limp the rest of the way without a clutch or get it it towed. I drove mine for a couple of months with T-O bearing noise before doing my clutch.
07-10-2013 08:55 AM
Polishmagnum Anyone out there? Anyone??
07-09-2013 07:27 AM
Polishmagnum I know this is an older post, but I finally have the time and money to do this! Order the Luk clutch kit from ebay for about $110, now another question. Knowing my TOB is likely toast, and the shop is about 20 miles away, would y'all attempt to get it there with RPM shifting or just get it towed? In a nutshell, can I trash something else by trying to save towing? Thanks in advance!
05-05-2013 10:53 AM
Jerry Bransford It's not an intricate job, it just involves some good old-fashioned hard work you can finish in a day. What I would buy or rent ahead of time is a transmission jack which will make the job a lot easier. Harbor Freight Tools has a pretty good one for $50-60 or so.
05-05-2013 10:18 AM
jricher82 Depending on where you go, a clutch job could run you anywhere from $600-$1000, parts and labor. I've done a clutch kit job on my TJ a few years back with a buddy and common hand tools. It's really not that difficult if you can set aside a day, get yourself a good clutch kit (i.e. not DuraLast Autozone brand) and get under there and have at it. Here is a link to a great write up to give you a good idea of what's involved : 1997 Jeep TJ Clutch Replacement
05-05-2013 06:32 AM
Polishmagnum Also how involved is it to put one of the kits Jerry mentions in? I'm fairly handy, but also dont want to get involved in a very intricate gearhead project right now...If I would pay a mechanic, what would be a ball park install fee?
05-05-2013 06:17 AM
Polishmagnum Yea I meant the brake fluid in the clutch reservoir...haha not a total newb.... but thanks for all the advice folks, sounds like I know what I need to do. I just put a new top on that thing, donesnt that ALWAYS happen? Jazz it up and something burns up HAHA
05-04-2013 01:39 PM
Jerry Bransford Yep a whine that occurs only when the clutch pedal is being stepped on is caused by a bad throwout bearing.

Might as well replace the clutch, pressure plate, & pilot bearing too while you're in there. Go with a 05-065 Luk replacement clutch kit which includes the clutch disk, pressure plate, pilot bearing, throwout bearing, and pilot shaft. You can sometimes even find that kit occasionally for <$100 on eBay or amazon.com.
05-04-2013 01:39 PM
4X Junkie
Quote:
Originally Posted by distortedtj View Post
For the wine in your trans with the symptoms you list...Your throw out bearing is most likely done for.
I second that. The bearing will cause a swirling noise when it is starting to go.
05-04-2013 01:28 PM
distortedtj The brake fluid is not in question with the clutch. Has nothing to do with it. You do have a clutch fluid res that will be on the drivers side firewall closest to the fender. It is all black.

For the wine in your trans with the symptoms you list...Your throw out bearing is most likely done for.
05-04-2013 01:21 PM
Polishmagnum
97 TJ Clutch/Tranny Whine

So about an hour ago I was coming home in the Jeep, and at a stop light it started making a whining noise. So I come to realize its only doing this when the clutch is pressed down. No shifting problems, didnt really notice anything else but the sound. Its high pitched and loud, and again, only when the clutch is pressed down. Even if you just touch the pedal, it starts. So I had the kid work the pedal and I looked underneath, of course the sound is super loud under there (HAHA) AND I noticed smoke or haze when the pedal was pushed. Clutch burning up? I checked the brake fluid reservoir, and it is full, so.....any help? suggestions??

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:53 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC