Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Clearing codes.

Join Wrangler Forum Today


Thread: Clearing codes. Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-07-2013 06:43 AM
1979WagoneerLTD The following procedure has been established to assist technicians in the field with enabling and running OBD-II Monitors on RWD/4WD trucks and Jeep models equipped with Jeep/Truck Engine Controller (JTEC). The order listed in the following procedure is intended to allow the technician to effectively complete each monitor and to set the CARB Readiness Status in the least time possible.

By performing a battery disconnect, or erasing diagnostic trouble codes, the CARB Readiness and all additional OBD information will be cleared.

The following is an outline of the Monitoring Run Process, including suggestions and tips in order to aid in the process of meeting the enabling criteria for these monitors. The most efficient order has been outlined below. For example, the first two monitors have very similar enable criteria; it is possible that the Evaporative Leak Detection Monitor will run during the O2 Sensor Heater Monitor.

This monitor requires a cold start, usually an overnight soak or parked for at least 8 hours without the engine running. The engine coolant temperature must be within 10 degrees of ambient/battery temperature, and the sensed Ambient (outside) Temperature must be between approximately 40F and 90F.

Misfire monitor is continuously running during engine operation. For the Misfire monitor to be enabled, the Adaptive Numerator must be learned since battery disconnect and every Key on there after (known as Power-on learning).
To allow the PCM to learn the Adaptive Numerator, the following must happen:
Open Throttle. Engine Cool Temp Above 100F Or If Below 100F, Wait For ECT Rise Of 59F.

This monitor requires a cold start, usually an overnight soak or parked for at least 8 hours without the engine running. The engine coolant temperature must be within 10 degrees of ambient/battery temperature, and the sensed Ambient (outside temperature) must be between approximately 0F and 100F. The monitor should run directly after starting the engine.

The vehicle will need to be driven at a steady highway speed for a few minutes. The monitor will typically enable and start running at approximately 35 to 40 MPH for 2.5L and 4.0L engines, 50 to 60 MPH for all others). If the vehicle is equipped with a manual transmission, using 4th gear may assist in meeting the monitor running criteria.
The vehicle will need to be driven for a period of time at a steady highway speed. Approximately 35 to 40 MPH for 2.5L and 4.0L engines, 50 to 60 MPH for all others and brought to a stop for a short period of time with the A/T left in Drive. The O2 Monitor will not run in Park or Neutral, except for vehicles equipped with a M/T.

The Purge Free cells must be updated before the monitor will run. The enabling conditions are similar to the O2 Sensor Monitor enabling conditions such as, the vehicle will need to be driven for a period of time at highway speeds and brought to a complete stop. The Purge Flow Monitor will attempt to run every OTHER throttle closure. If all of the parameters are met and it still does not run, with your foot firmly on the Brake, quickly open and close the throttle, this will allow another Purge Free update, and then the Purge Flow Monitor should run.

The Adaptive Numerator is a software learning routine that tells the PCM where the crankshaft slots are. Since every crankshaft is different, the PCM must learn exactly where its particular crankshaft slots are; otherwise its RPM calculations would be wrong. After a battery disconnect and then a power-up of the PCM, the Adaptive Numerator is set to a value which it would be at if everything were perfect (crankshaft slots, sensors, PCM hardware, etc.). If the Adaptive Numerator is equal to the default value, no learning has happened and the Misfire Monitor will not run.

Hope this helps.
05-06-2013 02:02 PM
olivajcarmine I was told 100 miles by my mechanic
05-06-2013 01:56 PM
PA Blondie Not sure on the Jeep but on our Mustang it was 50 miles
05-06-2013 01:01 PM
Neil F. It is not a fixed number of miles or anything to do with the ke. It varies depending on the sensors but it should all be set by 40 miles.
05-06-2013 12:31 PM
bondosgto I read some where 40 key cycles, maybe it was 100 miles. Dunno which one exactly.
05-06-2013 12:30 PM
Bet For my code it was about 125+ miles and then the mechanic would approve and sticker it up.. light came back on soon after I rolled about 125 miles.
05-06-2013 06:24 AM
Horn5413 Someone on here has to know how long this thing has to be driven to be ready for an emissions test..
05-03-2013 04:11 PM
Horn5413
Clearing codes.

I disconnected the battery when I installed some off road lights. And it must of reset the ECU. Well I took it in for a good ole NYS inspection, and it failed because 3 out of the 8 sensors didn't run yet. So my question is does anyone know how long this needs to be driven and what driving conditions.. There were no codes I just need 6 of the 8 sensors to run for the state to pass it... It is a 2001 TJ 2.5l. Thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 12:38 AM.



Jeep, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC