Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Build Forum > aussie locker

Join Wrangler Forum Today

Thread: aussie locker Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-06-2013 01:41 PM
89sierra im going to but now that im thinking of this. if not the axle out of my 95. its the axle out of another jeep so i am not sure as to what the year is.
05-06-2013 01:39 PM
indirocz28 I do agree if upgrading.
05-06-2013 01:21 PM
YJ fanatic I would ditch it then. There is no need for it. The outer shaft holds the inner shaft in.
05-06-2013 12:45 PM
89sierra mine only has one on the right side holding the stub shaft in there. i emailed aussie and he said to ditch the one c clip holding the shaft in. i would love to do the tj shaft but i do not have one right now or access to one
05-06-2013 10:23 AM
YJ fanatic
Originally Posted by roadyrob View Post
your 95 requires c clips to hold the axles in. early yj's didn't.
I think its the other way around. Early jeeps had them, but after a year or two, they realized they didn't need them, so they ditched the c-clips. They were gone by 92, because mine doesn't have them. And my buddy's 95 doesn't either.
05-06-2013 09:20 AM
roadyrob your 95 requires c clips to hold the axles in. early yj's didn't.
05-06-2013 07:50 AM
indirocz28 I was just going off of my C8.25 rear Aussie install into my Cherokee last fall.

Being that this is going on a front axle, and the front is held in by a nut, bearing and washers, it may not require a C-clip inside the diff.

Either way, do the TJ axle swap though.
05-06-2013 07:38 AM
YJ fanatic I just put mine in last weekend, and mine didn't have c-clips. Didn't even have channels for them. But even if your axle does have them, I don't see how you can reuse them. There's no way to get to the end of the shaft after the locker is in there.

And if there is a c-clip, it'll only be one, on the passenger side. They say they just put it on there to jeep the inner shaft in place during assembly. So once the outer shaft is in, you don't need the clip anyway.
05-06-2013 03:08 AM
indirocz28 C-clips get reused. Also do the TJ upgrade and save yourself the trouble of messing with that half axle BS.

Next option is to find a D44 from a JK..

Make sure you check and log your tolerances for your Aussie.
05-06-2013 02:07 AM
aussie locker

hey guys new to the forum. i just picked up a 95 jeep yj. i am looking at swapping in another dana 30 that has 4.88's in them already but the front is an open carrier. i purchased a aussie locker for the front but i am not sure what to do with the c clipe if it gets reused? tosed out? i know about the tj shaft but i would rather not go that route now and just use what i have.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 12:09 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC