|05-08-2013 09:14 AM|
|flynhi4u||Good one Red Surveyor! I never had a set, trying to get a set for our new soft top and doors. I checked Quadratec but they do not carry the nuts, just the inserts. I need the nuts so I can put our half door hard tops on for next winter.|
|05-08-2013 08:42 AM|
|05-08-2013 08:35 AM|
|flynhi4u||Still trying to find the nuts that go on the bottom of the door inserts. Anyone have a clue where to find them?|
|05-07-2013 12:54 PM|
I have found tons of the inserts for sale but can't find the page where I saw the nuts that go on the bottom of the inserts. Anyone have a clue who sells them or even a part # for them? Thanks
|05-07-2013 12:42 PM|
Thanks Waterdog! That is the ticket! I will order a set and the nuts. BTW, if you were to put a single wrap of .032 safety wire around the metal tabs that hold in the nuts the chances of pushing the nuts down out of the clips would be greatly reduces. A plastic tie strap would work too, so long as it did not interfere with the insert going back down into the hole. I think safety wire would be a safer bet. Thanks again. This site is AWESOME
I had actually seen the nuts for sale somewhere but until I saw the pic I was not sure where they went.
|05-07-2013 10:55 AM|
|Water Dog||The nuts at the bottom of my inserts that hold the hard door uppers are simply a round internally threaded piece that is only held in place by the four prongs on the insert. In fact, if you push down to hard on the bolt, you run the risk of popping them out, so it would be easy to simply remove the inserts (pry up and turn 1/4 turn) and take out the nuts, then reinsert the inserts when you are ready to use the soft uppers. Here's another source for inserts if you need something other than black. Original Replacement Parts 5FB63RTB - Door Pin Insert in Spice for 87-02 Jeep® Wrangler YJ & TJ - Quadratec here are a couple of pics of mine.|
|05-07-2013 10:51 AM|
|GoldenSahara00||Sounds like a plan to me. Or just make the middle insert threaded or something and leave the other two normal, etc. Get a little creative let us know if you need anything else.|
|05-07-2013 10:40 AM|
|05-07-2013 10:28 AM|
Well if they just slide down into the inserts then I guess if the nuts in the bottom of the threaded inserts hold them up too high them I could modify the bottoms of the pins on the half door soft door frames. Maybe I could cut off the bottom of the pins and weld a smaller diameter rod to it. Then the smaller rod could do down through the threaded insert. Just a thought. Won't know for sure till they get here what I will be faced with. thanks for the info. Will let you know what I figure out.
|05-07-2013 09:56 AM|
|GoldenSahara00||I know about the threaded inserts, but I am not sure if they are compatible. The soft door uppers just slide down in, that's all that holds them. So yes, no retention.|
|05-07-2013 07:38 AM|
In doing a search for door inserts I discovered that they make threaded door inserts that the bolts for our hard upper door tops would thread into. If I get a set of new threaded inserts can I still use the soft top doors with them or does the nut in the bottom of the threaded insert keep the rods from the soft door frames from going down into the door far enough? What holds the soft door frames in the door anyway? I don't have a set yet but to me in the pic it looks like they just have three steel rods that go down into the door inserts. Is there no means of retention to them? So many questions.....
|05-06-2013 01:14 PM|
Thanks again, your help is much appreciated.
|05-06-2013 10:51 AM|
|GoldenSahara00||They pop right in. I think you turn sideways and push down, then turn 90 degrees and they pop down in the rest of the way. Something like that. I only know because I had to replace one of mine once upon a time. Goodluck cutting the welded nut off, gota love previous owners...|
|05-06-2013 10:40 AM|
That looks like them
Many thanks. I did not know what they were called but that looks like the critters I need. Guess I will be grinding the welded on nut off the door so I can install the insert. Will have all summer to figure out what to do to the door to hold the hard half door frames on for next winter.
I am curious, do these inserts just pop in or do I need to remove the interior trim panel to install them?
|05-06-2013 10:34 AM|
I believe this is what you're after
Rugged Ridge Part rug11819.15 - Half Door Inserts
|05-06-2013 10:29 AM|
1/2 door frame question
In preparation for our new Softtopper top and new 1/2 door frames and skins I took off the drivers hard top half of the half door of our 99 TJ yesterday. The PO installed a set of hard top half door skins with sliding windows. For summertime driving we want a soft top with soft door uppers. Anyway, I can't find any info on the solid door upper we have. My luck that they have no markings on them. My issue is this. When I removed the hard door uppers I noticed that the hardware that holds them on are kinda like a concrete anchor in that they spread out inside the door when tightened down. I am thinking I am missing a insert of some type that would normally be in the top of the half door as what I am left with is a square hole about 5/8" square on the two back holes. From the looks of the soft top door frames they use round steel rod maybe 3/8" dia. I am not a genius but I am thinking round peg square hole equals problem. The front hole is even better as someone tack welded a 3/8" nut to the whole for the front hold down bolt of the hard door upper to thread into. I have been trying to find a parts breakdown of the half door online but no luck so far. So is there some sort of plastic or nylon insert that goes in the two rear holes on the top of the half door frame for the upper door frame pins to go into? How about the front hole? With the nut welded on ours I was unable to deterring what type of hole was in the door. Thanks in advance.