|Today 07:23 PM|
|Today 05:25 PM|
|Today 11:52 AM|
|Today 04:47 AM|
A couple years ago I had an 05 sport that I rolled, then built a 96 Xj which I just sold.
Picked up this cherry little 03 Rubicon, appears to be stock with what looks to be a synergy cage. The kicker.... It's a 2003 with only 25k miles!
|Yesterday 10:17 PM|
|jmo_13||Drilled 4 drain holes in the frame. That is all.|
|Yesterday 09:14 PM|
|Yesterday 08:31 PM|
|NYjeeper_TJ||Tryed to figure out why both windshield washer motors aren't working. Motors are good but now power to them. Couldn't find a fuse. Oh well don't need them till winter anyway|
|Yesterday 07:59 PM|
|Yesterday 04:59 PM|
|Yesterday 01:41 PM|
|sebztj||finished installing my KC lights last night after my tj had a shortage|
|Yesterday 01:39 PM|
|Yesterday 01:12 PM|
|Yesterday 12:51 PM|
|Yesterday 11:56 AM|
|Yesterday 11:55 AM|
Rotated my tires in the garage in the tx heat
Omg I need to invest in an impact drill. I spent most of the time removing and installing the wheel bolts!
|Yesterday 08:51 AM|
Repacked the back using new case.....
|Yesterday 08:14 AM|
|thedawgshow||Just stared at amazemnt to the fact that there is no gear oil leaking onto my garage floor for over 24 hours for the first time in a long time!!!!|
|Yesterday 03:10 AM|
Replaced my hub asbly today.
|Yesterday 01:26 AM|
Before i swapped fenders, i had normal stock fender flares on(Not the 1" extended sahara ones). Using a plum die, i measured over the fender down to the tire tread. My 31" duratracs jutted out about a half inch. With the tube fenders, they come out about 1 1/2". So you lose about 1" in coverage going from stock to 3" tubes. This wasn't a big issue for me, as it's barely noticeable to the naked eye. And my Jeep passed inspection just after installing these, with no mention of tire coverage. Though this will vary depending on how picky your inspection place is.
If you want to go the 100% legal route, you'll probably want to go with the 4.5" fenders. But from what I've collected about coverage laws and how they're enforced, the general idea is that as long as they're not jutting out an extremely noticeable distance like 3", you'll most likely go unnoticed. Besides, there's plenty of other *technically* not legal things on my rig I've never gotten stopped for.
And if all else fails, I've heard of people using that plastic garden edging to make their own make-shift flares.
Hope this helps!
|Yesterday 12:39 AM|
Those fenders are on my list BUT i'm not sure if I need 3" or 4.5" (other brand of fender). I MIGHT run 1" wheel spacers in the future but that's a maybe.
Here's how she sits now:
|Yesterday 12:27 AM|
|mikhail2400||Man I want those tube fenders!! nice work|
|Yesterday 12:10 AM|
Well, my annoyingly-long journey to replacing my fenders is at a close. Finally have my C&C Fabs 3" flare tubes on. I enjoyed wiring my new side markers, as i got to play with diodes & resistors. And i enjoyed learning a bit of fabrication in repairing my brush guard, and making the brackets for my side marker.
Other than that, i got brand new front brakes for inspection. Painted my calipers red while i was in there to add a splash of color behind my wheel spokes. She's sittin' pretty again. Until i break something else that'll require me to upgrade
|07-21-2014 10:53 PM|
|Doc_H||clay bared and waxed her now she looks brand new ps she is a 99|
|07-21-2014 09:27 PM|
|SolarColumbia||Sanded, epoxy primed and painted rust spots on fender around bolt holes for fender flare. Painted brake drums with one coat Rustoleum Rust Reformer followed by Rustoleum gloss black. One rear wheel was torqued on to like 200+ foot lbs and I broke a flex head and an extension getting the lug nuts off. Had to use 2 ft length of pipe over the tool and pull really hard. Will have to replace some tools and probably pick up a 40" 3/4 drive breaker bar in case this ever happens again. First time taking wheels off since I got the Jeep so I don't know who to 'thank.'|
|07-21-2014 08:00 PM|
|DBoat||rinsed the dirt/dried mud from my tranny cooler|
|07-21-2014 06:33 PM|
|ChaTownTJ||Installed two clamp collars on my sway bar. It has been shifting and rubbing the frame on the driver's side, which made this terrible screeching sound. Ordered from McCaster-Carr on Saturday and received them today. First "modification" I've made since I bought it. Big moment!|
|07-21-2014 05:23 PM|
|WIwrangler||Changed the oil made some zipper extensions rubber coated the flares and made my own light bar just need lights now lol busy day oh and made my own grab handles Also cracked the windshield installing the light bar|
|07-21-2014 10:14 AM|
Oh.... and gave her a bath, then drove her to town to welcome my sister back in town and let my boys play with their cousin. Then off for take out and all in a topless and doorless TJ
|07-21-2014 01:29 AM|
|07-20-2014 10:42 PM|
|This thread has more than 30 replies. Click here to review the whole thread.|