|07-06-2013 06:01 PM|
|Neral22||Thank you Matt! I stole your idea today and it came out nice!|
|07-02-2013 02:40 PM|
|Scott-CJ8||Looks great and very crafty. I would recommend adding a spring to the antenna (like Hawaii 50 said).... you know you're gonna hit something sometime....|
|06-29-2013 06:32 PM|
|Neral22||Wow! I am glad that this thread got pushed forward! This would be great for what I want! Thanks a bunch!!|
|06-29-2013 05:58 PM|
I like your antenna setup. I'm considering following your plans.
After having yours on for a while, do you see a need for a spring at the base to relieve some of the stress in the plastic license plate holder when you hit the antenna on something?
I think I may have to use a spring at the base just to get a 3 ft antenna slightly above my roofline. I can't use a 4 ft antenna if I want to park in my garage.
|06-04-2013 12:49 AM|
|06-01-2013 09:03 PM|
|RAINSTATEBEAR||Did you add any RTV or anything around the top hole to keep water out?|
|05-12-2013 01:42 PM|
|05-08-2013 11:05 AM|
|DurbJKU||Doing this today. Best I have seen. But how do you run the wire into the cab?|
|04-02-2013 11:29 AM|
|mattdenney07||Yeah it works great. With the 5 ft fire stick, I tuned it down to 1.2 really easily.|
|04-02-2013 04:24 AM|
|mikejoel||Not a bad setup. Might try it too. Would you get a good signal with it?|
|04-02-2013 12:57 AM|
|04-01-2013 10:21 AM|
|Scott2373||That's a really nice, clean set up! Nice job!|
|03-29-2013 05:05 PM|
And here's a little cheat sheet for setting up the antenna properly on the mount. It was a few days before I found this and was wondering why my antenna wouldn't tune properly. Having your metal and plastic washers in the right order really helps out!
|03-29-2013 04:59 PM|
Crafty little CB Antenna mount on a budget
I did this about 8 months ago, but never shared it. Still holding up strong!
I ended up getting a 5 ft Firestik Cut-to-tune antenna from a friend for $10 and needed a cheap way to mount it. Couldn't really mount it on the tire carrier because the antenna was so damn long. The only other option that I really liked was the CoolTech Ultramount, but $90 for an antenna mount? That cost more than my CB radio and antenna combined!
I still liked the concept of that mount tho, so I decided to copy it and save some cash. I started with a cheapo Firestik 3-way mount. Amazon sells them for $20, but I picked it up for about $15 at a local offroad shop.
Firestik 3-way Antenna Mount
Take the license plate off
Pop out the front plastic inside the license plate bracket
From here, you can see pretty much what I did. Drilled a hole in the top of the license plate holder big enough for the antenna after I'd lined up the antenna mount. Then drilled 4 holes in the forward side of the mount big enough for the bolts that I used. I don't remember the sizes, but you can eyeball it and be just fine. From there, I cut a length of some 14 ga. wire I had laying around and put some terminal lugs on the ends. Put one lug on a bolt for the antenna mount, and ran the wire down behind the mount underneath the body of the jeep. I drilled a hold big enough for a bolt in the frame, ground some paint off, and threw that bolt and terminal lug on. Now the mount is grounded and you're pretty much good to go. If I skipped any smaller steps, they should be self explanatory. There's lots of eyeballing and guesswork in this, so you can definitely make it your own. Any quesions, feel free to ask!