|05-09-2013 04:47 PM|
|05-09-2013 04:18 PM|
I've found this chart helpful:
Jeep Tech: Tires
|05-09-2013 04:04 PM|
Even though it has bump stops you still may need longer ones.... Some lift kits say "designed for 33" tire". Hence you should be ok.
Now if you have anything other than stock setup(ie no trac or sway bars) this may cause issues with rubbing. IMHO get the 33's, get the lift kit, put it all on and see where your at. At best some tj fender flares can do the trick at worst you'll be gettingout the sawzall. LOL!
Btw what engine, trans, axles do you have? Just be aware the d35 rear end can be kinda weak especially with 33's if your hard on it. Are you going to offroad at all or is this a DD mostly?
|05-09-2013 03:51 PM|
|05-09-2013 03:41 PM|
I need to check mine in the rear and make sure the bump stops are working as designed. They came w/the kit so you'd think I wouldn't have trouble.
Will check it out...
|05-09-2013 03:38 PM|
|05-09-2013 03:27 PM|
BUMP STOPS!!!!!!!!!!! You should have no problems with 33x12.5x15's with a 4" offset rim. With a 3.5" list and proper bump stops.
I run 36's with 2.5" lift springs. + some other fun....
Just don't over lift. Unless you want a monster truck.
|05-09-2013 02:02 PM|
|05-09-2013 01:53 PM|
dont confuse fenders with flares. Flares are plastic, fenders are metal. When I flex the front, the back tire not only rubs the plastic flares but pushes under it up the metal of the body. If I don't back off it, it will cut the tire. This would still happen without flares...
not my pic but this gives you an idea... its a 33" tire w/o a lift. With a 4" lift, when driving the front left onto something this is what the right rear looks like.
|05-09-2013 01:43 PM|
|05-09-2013 01:39 PM|
|05-09-2013 01:36 PM|
|GoldenSahara00||I have a cut wheel on my angle grinder that will fix all your problems.|
|05-09-2013 01:33 PM|
|05-09-2013 01:29 PM|
|jordan yj||Awesome thanks everyone!|
|05-09-2013 01:28 PM|
^ Ditto that... "The largest tire you can run on a stock YJ suspension is a 31"
I had to install a 4" suspension lift to clear 33 12.5's and I still rub on the trails. I need another 2" as it sits...
|05-09-2013 12:15 PM|
As for the size you'll need once your lifted, any wheel with a backspacing of 3.75" or less will fit just fine. There are tons of Jeeps running a 33"x12.5" on a wheel with a backspacing of 3.75" with no rubbing.
Hope this helps! If you have any questions please let me know.
|05-09-2013 11:23 AM|
Nope. 33s will rub badly on a stock suspension, even w/ offset rims.
You need a lift, or radically revised fenders (flat fender kits) or a combo of both.
|05-09-2013 11:13 AM|
|bigb996||I personally would buy the lift and then the tires. If you put 33s with just a shackles it will look awful and ride as bad if they will even fit. I think you would be better off with a 1" body lift rather than a shackle lift as well. Replacing shackles is pretty pointless.|
|05-09-2013 11:06 AM|
|wrangleryj90||I don't think you can clear that size even with shackles unless you want to go over 1" which I would not|
|05-09-2013 11:02 AM|
|jordan yj||I am new to the forum as I just bought my first Wrangler. I want to put Mickey Thompson Baja MTZ's on my 95 and don't know about what size wheel to go with them. I want the tires in a 33X12.5. I was told that with the proper offset wheel that the stock suspension with shackles will clear them. I also have a 3.5 inch suspension lift planned for the future. Can anybody tell me what wheel size and offset I need please? Any other advice about tires/suspension/ fender clearance for a newbie would be greatly appreciated!|