Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > 97 Wrangler need to hotwire/bypass pcm emergency start needed

Join Wrangler Forum Today


Thread: 97 Wrangler need to hotwire/bypass pcm emergency start needed Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-10-2013 08:22 PM
JeepersDave Sorry, meant to show the ground terminal

I I I
-- < ground
--
05-10-2013 08:19 PM
JeepersDave I'm not aware of any way to bypass or Hotwire the PCM.....however, when my 97 experienced major "brain farts" I found that you can run a jumper wire from the ground on the ASD relay to the ground on the Fuel Pump relay and in many cases force the PCM to accept the situation at hand and let the engine start and run.

Before you try this, disconnect BOTH battery terminals for at least a minute. WITHOUT a battery in the loop, touch the positive and negative cables together for about 15~30 seconds. This will reboot the PCM and it will go into its relearn stage. I cannot emphasize enough that you must not have ANY connections to your battery when doing this.....NONE!

This hasn't always worked for me, but it has not hurt anything to try it.

The PCM sends ground signals to activate the relays, the 12v power is already there. The fuel supply will energize before the ASD can go to default and since the PCM supplies separate ground signals, you're just kinda making sure everybody's there and ready to play the game.

Best of luck
05-09-2013 08:07 PM
RUBI 4 MY MRS You are going to have to find out why it is not getting power. What caused the battery to run down?

Have you checked all the fuses in both places (PDC & fuse block)? What happens when you turn the key? Anything in the cluster work or gauges move? Got headlights, wipers, radio? Make sure the cable from the B+ post to the PDC is good both at the battery & the bolt where it attaches to the PDC. See if fuse #3 in the PDC is good. Then pull it & verify it has 12v at one terminal. That is the main power source to the ignition switch.



Any other info you can think of might help.
05-09-2013 06:48 PM
XDR Turn key to run, then jump the starter from power to signal. Not 100% that will work.
05-09-2013 06:07 PM
Falcho
97 Wrangler need to hotwire/bypass pcm emergency start needed

Hi kids of all ages,
I have a friend, who has a 97 wrangler, 4.0 auto. He lives very remote in the bush here in Alaska. The battery ran dead on it, and when replaced, the infamous no start no gauge no check engine light happened. the CPS and the other usual suspects have been checked with a no go. Theres no way short of an air lift thats going to get this jeep out of where its at, unless we can get it to start. So, we need the info to hotwire this bad boy to bypass all the evil the pcm is doing. Not worried about what accessories work or not, just that it starts so we can get it to a road to trailer it back to town. Does anyone know a quick and dirty way to get this bad boy fired up? Dont want to have to do more then the absolute minimum to get it out so as not to compound problems. Help us Obi Wan Kenobi, your our only hope! Or, any of you other jeepers out there
Any help would be appreciated. Thanks in advance

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 03:43 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC