Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > General Jeep Discussion > Winch problem

Join Wrangler Forum Today


Thread: Winch problem Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-17-2013 08:42 PM
30-284 Make sure that the small wire that picks up the relay is putting voltage to the small terminal on the relay. That would be the one that comes from the controler, also when you use the controler to operate the winch, can you here the relays pick up? Do these relays have 1 small terminal or 2 small terminals, if one then they are internally grounded and need a good ground at the mounting bolt, if 2 then they will need a small ground wire at the second small terminal on each relay.

Donn
05-13-2013 06:26 PM
OregonPlinker Nope. It wasnt a ground problem. Got it all cleaned up and made sure its got good ground... Still nothing. Any help would be appreciated. Thanky
05-12-2013 11:06 PM
OregonPlinker Bad ground is what im thinking. Gonna take it apart tomorrow after work and make sure the solenoids are grounded. It has a lot of rust on the solenoid panel...
05-12-2013 08:58 PM
OregonPlinker
Winch problem

I hope this is the right spot for this thread. Bare with me.

I have had this winch 3-4 times over 10 years. Me and my cousin keep selling it back to each other. Its a WARN MX 10000 D1. Last time I had it it worked. My cousin had it and it quit working. We decided it was the solenoids. I got it back from him for my wrangler.

I bought 4 new solenoids for it and put it on my wrangler today. I got it all wired up and nothing is working. I have juice at the winch, at the remote and at the little wires and little posts on the solenoids. Nothing at any of the big posts except the one that is hooked up to the battery. But even that solenoid isnt putting power out the other side when I hit the switch. I am pretty sure I got all the wires back where they go. I numbered them and drew a diagram to be sure... I also looked at my WARN 8000 thats from the same era with the same solenoids and its wired up the same. Im lost. I dont understand it.

The solenoids are heavy duty continuous use or whatever from napa. They arent like the ones you see on ebay with all the posts on top of the cylinder. They are like the ones off an old ford with the posts on the side of the cylinder... Hopefully you know what Im describing...lol. Any help would be much appreciated!!!! Thank you, Brandon

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 01:24 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC