Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > About to do the Nutter Bypass

Join Wrangler Forum Today


Thread: About to do the Nutter Bypass Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-17-2013 08:00 PM
Nubby55 I did the By-pass and all was so much better, and then I change the Carb. to one for a late 70s early 80s CJ7 with no stepper motor, bolted right on every thing hooked right up NO MODS no Adapter plates, and runs like New!
05-17-2013 12:07 PM
indirocz28 Well Keymo, I will follow your guide and do it on my 4.2L this weekend.
05-17-2013 11:09 AM
Keymo Good luck, man! It's super easy once you get everything figured out conceptually. Here's my thread that I started when I started the project out... Sadly, I didn't really get any help with it - but I documented what I did and anything I ran into pretty well so that others with similar carb situations could have some help. Don't know why I JUST thought of it.

http://www.wranglerforum.com/f8/nutt...or-170154.html
05-17-2013 11:04 AM
combsn87 awesome, I have to head up to D.C. Tomorrow for a week to work from the office. and then ill have to tackle this in 2 weeks when i get back.
05-17-2013 08:12 AM
indirocz28 Also, do not adjust your air fuel fixtures without a wideband o2 sensor so you don't cause more issues by running lean/rich. I know its a crazy thing to have on a jeep, but you can make it so that it is modular and use it for several different vehicles.
05-17-2013 02:16 AM
Keymo No. You don't have to worry about it. Though in your case the bypass is "needed" You computer is trying to get information from stuff and control things that aren't even there...

When I got my YJ it has a carb off of a '72 Dodge (Still the Carter) which I didn't figure out until I was doing the bypass as well. Make sure everything else is hooked up and connected the way it should be according to the bypass instructions. It ended up making a world of difference for my YJ.
05-16-2013 07:52 PM
combsn87 so i started this you know, dug in cut wires and what not..and found out that my carb was already bypassed. but not the same way. If you look at picture 4 there is a plate covering where the stepper motor used to be. so i am guessing i dont have to worry about the ecm controlling the carb?
05-16-2013 03:06 PM
combsn87
Quote:
Originally Posted by luebkeb13 View Post
Hope this pic helps you out.
Thanks alot!
05-16-2013 03:03 PM
luebkeb13 Hope this pic helps you out.
05-16-2013 02:59 PM
luebkeb13 That is the stepper motor plug. Those bottom screws are to adjust your fuel/air mixture.
05-16-2013 02:32 PM
combsn87 one other question. on 4x4wire is says this..

The following steps all apply to anyone keeping the BBD carburetor. Steps one and two may be skipped by those changing to another type of carburetor or to fuel injection.
  1. Warm up the Jeep long enough for it to be operating in closed loop mode if the ECM is still functional.
  2. Screw in the idle jets so that the needles that are controlled by the stepper motor move. The purpose of this is to fool the ECM into putting the stepper motor driven needles into the full rich position. When this happens, you will see that the needles will be all pushed the way to the inside of the carb and the tone of the air going through the carb will get much lower and the engine will slow down and start to miss. At this point you should shut off the engine and disconnect the plug for the stepper motors on the back of the carb. The plug stays disconnected from now




are the idle jets these?






and is this the plug for the stepper motor?









Just want to make sure before hand.


thanks again
05-16-2013 02:26 PM
BCDonny I use the motor craft 2150 from the eBay guy. Works great
05-16-2013 01:52 PM
combsn87 Awesome! haha thanks man. yes it will be getting replaced soon.

Quote:
Originally Posted by luebkeb13 View Post
Yes, this is the Carter 2bbl carb...it's a junker too
05-16-2013 01:48 PM
luebkeb13 Yes, this is the Carter 2bbl carb...it's a junker too
05-16-2013 01:37 PM
combsn87
About to do the Nutter Bypass

Can some one take a quick look at my carb and help me determine if it has the Carter BBD carburetor?

thanks,







Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:49 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC