Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Vibration and such.....

Join Wrangler Forum Today


Thread: Vibration and such..... Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-13-2013 08:46 PM
99wrangler99 Hey, I know this an old post but on gonna follow up on this issue I had a while back. I solved the issue of the steering hop, definitely was the rear drive shaft. I think the u joint was loose/warn. Found this out the hard way... let my brother drive my jeep...... get a phone call... the rear universal broke and due to that the drive shaft swung up and put a hole in my exhaust... but it did solve the issue of the hop haha.
05-17-2013 12:42 PM
SuicideSaints SYE kit of drop the t-case with washers until you get the SYE. The longer you wait the more wear and tear on the ujoints.
05-17-2013 12:07 PM
Jerry Bransford A tcase drop is not normally even close to being enough to get rid of the vibrations caused by a suspension lift as tall as 4". I HATE it when shops sell 4" suspension lifts to unsuspecting SWB Wrangler TJ owners without telling them they are likely to develop serious vibrations until they get a SYE & CV driveshaft installed. I suspect they don't tell them because of how much more $$$ installing a SYE & CV driveshaft adds to the cost & that the customer may decide to do nothing. Once the 4" suspension lift is installed, they're stuck.

In the mean time, you can't just "live with" those vibrations which can start taking out the u-joints, seals, etc. I would drop that t-case down another inch until you can get a SYE/CV driveshaft. That additional inch should help a lot.

The front vibration could be nothing more than imperfect tire balance. The bigger thet tire, the more critical tire balance becomes.
05-17-2013 11:48 AM
99wrangler99 yeah I dropped the T case, and put brand new universals in, could there be something wrong with my tranny? or t case? I do not currently have a sye kit installed, I should but ill do that a bit later down the road
05-17-2013 11:23 AM
GoldenSahara00 With a lift that high, you are probably going to need a slip yoke eliminator and a new driveshaft. In the mean time you could drop your tcase using washers in order to drive, or order a tcase drop kit.

Here's something to read over on JF put together by UnlimitedLJ:

http://www.jeepforum.com/forum/f9/wh...nt-one-854790/

Start at "lifting your jeep" then go back up to the top.
05-17-2013 11:19 AM
rollistj With the lift did you also have a SYE kit installed? This maybe part of your problem. I have a 4" lift on mine as well but I dont experience the shake in the steering column. I only have a vibration under acceleration due not having the SYE kit yet.
05-17-2013 11:09 AM
99wrangler99
Vibration and such.....

I have a 1999 jeep wrangler tj sport with 4.0. So I recently had a 4inch lift kit installed, now a few weeks later I noticed a lot of vibration and the steering wheel shakes up and down. This also happens with the steering column. I replaced the ball joints previously and had the the front end aligned so it does not seem to be a death wobble, I replaced the front and rear universals and it took a lot of the shaking away but... when I drive at 35 mph the steering wheel starts to shake up and down again a little, and I can definitely feel vibration when i push the throttle mid way like somethings not rotating in circle. no clue what is happening! The vibration does go away when I push the clutch in. Any help would be greatly appreciated. Also I have power steering issues i think? I hear a loud whining noise when I tap the throttle. It will go quiet when I don't hit the throttle but the farther I push the throttle down the louder the whining noise gets... any help there would be good too.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:04 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC