|05-17-2013 01:40 PM|
|REEDracing94||It looks like your front fender flares are cut, which also makes the front look higher than the rear|
|05-17-2013 12:00 PM|
|SuicideSaints||The rocker is the bottom of the tub/body.|
|05-17-2013 11:59 AM|
|Aseventyfive||I'll buy and install tomorrow. Just need to figure out which ones to get|
|05-17-2013 11:58 AM|
just keep in mind with no bumpstops at all, like your current setup, there is nothing to stop the axle housing from smashing into the oil pan, or to prevent other significant vehicle damage during uptravel. your Jeep, your call.
|05-17-2013 11:54 AM|
|05-17-2013 11:53 AM|
|Aseventyfive||What do the rockers look like. Uber inexperienced.|
|05-17-2013 11:53 AM|
you need the whole bumpstop assembly...bumpstop cup, jounce bumper, mounting bolt, and bumpstop extensions for your shock length/tire size/etc.
look up a thread titled "correct bumpstop length"
|05-17-2013 11:50 AM|
|SuicideSaints||It doesn't look level but it is hard to tell. Measure from the rockers and see what that is. It might be the springs sagging from being worn out.|
|05-17-2013 11:45 AM|
|Aseventyfive||Also the rear bumper doesn't look level with the front. I thought that was because of the difference in lift from front to back.|
|05-17-2013 11:42 AM|
|Aseventyfive||Ok so I need bumpstops. What is their purpose?|
|05-17-2013 11:00 AM|
1) Pretty sure the bumpers aren't on the same level. So don't measure from them for a comparison. Measure from the front and rear of the rocker panel.
2) You have to determine bumpstops on your own. There's way too many factors for us to tell you how much you'll need. But you do need some for sure.
|05-17-2013 08:25 AM|
|ROBCAR||Does not look like your bumpers are inline with one another hence the 4" difference. Looks real close to level if you leave the bumbers out of it. Maybe I am not seeing what you are.|
|05-17-2013 06:40 AM|
|Aseventyfive||Here's the side view. Do I need the bumpstops? And are the other aftermarket parts good equipment or junk?|
|05-17-2013 12:54 AM|
|PHILDABEAST||Also has aftermarket sway bar links and is missing the bumpstop in the front.|
|05-17-2013 12:26 AM|
|thgr8alex||Can you post a pic of the side of your jeep? Also, what size tires are you running?|
|05-17-2013 12:24 AM|
|SuicideSaints||2 inch lift and I would say rancho shocks too. It is kinda odd that your are seeing a 4 inch difference between the back and front though.|
|05-17-2013 12:10 AM|
|EMTJEEP||The shocks look like Ranchos because of the silver metallic coloring.|
|05-17-2013 12:09 AM|
|jeepwayoflife||Yep I agree with above. 2" spacer lift in rear and I can't see any spacers from the pic of the front so I assume its a 2" or 2.5" lift spring. You also have aftermarket shocks, but I'm not sure what brand. Maybe rancho?|
|05-16-2013 11:59 PM|
|thgr8alex||You have a spacer lift in the back for sure. Looks to be about 1.5-2 inches and if you say the front sits higher then you probably have lift springs up front because theres no spacer up front. My guess is a 2 inch coil spring lift because actual coil lifts will give you slightly more lift than as described|
|05-16-2013 11:49 PM|
Is my jeep lifted?
My jeep looks like it sits higher in the front than the back. PO had mods on it but not sure if lifted. Took pics of the springs. I also measured from the ground to the front bumper which was 24 inches. Then measured from the ground to read bumper which was 20 inches. Thanks