Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > 89 YJ rear pinion seal question

Join Wrangler Forum Today


Thread: 89 YJ rear pinion seal question Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-17-2013 07:48 PM
Nubby55 I would not replace the nut I just tap the end of it a few times to renew the self lock and reinstall it.
05-17-2013 10:03 AM
Cashcrazy I have have replaced a pinion seal before just never on a d35 and I never replaced the pinion nut with a new one in the past. But if replacing the pinion nut is the proper way then I need to get one ordered. My impact should be able to remove the old nut. Thanks for your response.
05-17-2013 09:56 AM
Surfinglbi23 You do not need to replace the crush sleeve. I just did mine a few weeks ago. You just need to mark the nut location. Check out this video --> differential pinion seal replacement, Jeep Wrangler TJ, DIY - YouTube

The Haynes manual also details the procedure perfectly. It is very easy, a 10 minute job for me. Torque setting is very high, 180 lbs or so, essentially something the average person cannot overdo with hand tools. I hit mine with an impact wrench and kept checking it till it lined up. Did a run around the block and its been perfect since. 500 miles on her or so, no issues
05-17-2013 09:54 AM
OverkillYJ The crush sleeve does not need to be replaced. You can, but it is not needed. If you have never done a pinion seal before I can tell you from experience that the bolt holding it on is one tight SOB. At least for my Dana 30 it was, for my 35 it wasnt too bad, but this weekend I am doing it on my 8.8 and I have a feeling it will be worse than either of them. You are supposed to replace the nut though. Also before removing the nut count the amount of threads that stick out past the nut. When you put it back together it should be roughly in the same place. Getting accurate torque readings on it can be a major pain though. Even the new nut will probably be a pain to get on.
05-17-2013 08:50 AM
Cashcrazy
89 YJ rear pinion seal question

I am replacing the rear pinion seal this weekend. I have read that the 87-89 came with the non-clip dana 35. Removing the yoke and replacing the seal should not be a problem, but I have been reading about the crush sleeve. Will this need to be replaced also? Does anyone know the torque spec for the pinion nut?

Please share if you know of a good write up that covers this job. Thanks for any help.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 12:16 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC