Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Reinforcement plates for TJ frame rust? pics...

Join Wrangler Forum Today


Thread: Reinforcement plates for TJ frame rust? pics... Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-20-2013 11:10 PM
kyjeep I just put a frame under mine last month. If I'd have caught it when it was like yours I could have gotten many more years out of it. Just do the Eastwood and POR thing and you'll be good.
05-20-2013 08:50 PM
davidzimagery I've seen worse...mine. Started out having a body shop do a frame repair. After a closer check on the hoist, it was beyond a patch job. They found a good used frame and it's in the process of being installed. The rest of the Jeep is in good shape, and I had just gotten a new soft top and half doors. Not cheap, but it's a Jeep!
05-20-2013 04:13 PM
JimsJeep If you want to be proactive pick up a needle scaler HF has them pretty cheap and go at the rust areas to remove any scale. Then like others said coat it with POR 15 or something similar.
05-20-2013 03:39 PM
flynhi4u It has been my experience that welded repairs to boxed structures are very hard to keep from rusting internally and patches over existing steel leave a air gap between the two pieces that unless 100% air tight will start to rust and u can't see it because it is between two layers of steel. I think proper cleaning, treatment, and coating is a better way to go if u catch it early enough like u did.
05-20-2013 03:20 PM
Hamster Yea maybe I should just clean and treat it and keep an eye on it before I go weld butchering it. thanks for your input.
05-20-2013 02:42 PM
flynhi4u Like I said it does not look bad enough to go to that extreme but up to you. Personally speaking, if I was going to build that plate I would extend it up and down to the frame edges as it would be stronger tieing into the radiused edges. But again, I think welding on your frame from the pics u posted might be a be premature un unneeded at this time.
05-20-2013 12:52 PM
Hamster Thanks for the reply. It was driven a couple of years here in minnesota, but is now a strictly summer vehicle so I hope I can save it. Wish i hadn't driven it at all in winter but it was my only vehicle at the time.

The inside of those holes have the usual rust flakes, and the bottom inch inside the frame by the skid plate where the water sat is rusty, but the rest of the frame still has the cheap black paint inside, so I don't think it's too bad yet, I'm just concerned about the structural integrity of the frame at that bend on each side.

Was thinking of an oval reinforcement plate with additionaly welded holes on each end kinda like this super awesome ms paint drawing:
05-20-2013 07:15 AM
flynhi4u Looks like you caught it just in time. That really is not bad as I have seen them much worse. No expert but I don't think you are to the point that you need to start welding on the frame yet. What I would do is clean the frame and undercarriage with a pressure washer, drill drain holes in the bottom of the frame to let out all the water you put in it with the pressure washer. After the inside of the frame has completely dried, might take the better part of week depending on how much water is still trapped in it and how humid it is, take a long blow tool attached to your air compressor and blow out the inside of the frame. I have read where some people also use a shop vac with a hose attached that will go in the access hole of the frame. You want to get as much of the rust flakes out as you can. Eastwood sells a product to treat and coat the inside of boxed frames. It uses a nozzle that sprays in a circular pattern so it coats all four side of the inside frame area. The treat and paint the outside of the frame with something like Por 15. If you get proactive about it now and stay on top of it keeping the salt and mud washed out of it the frame should last you many more years. This is assuming that it is not so rusted on the inside of the frame and it just has not broken through to the outside yet, but from the pics you posted I did not see evidence of that.
We should all send Chrysler a big thank you for not doing a better job of treating the frames when they built our jeeps!!!
I was at Menard's Saturday and saw a YJ pulling a single axel trailer with a large load of laminated flooring on it. I checked out the jeep as I walked past it and like most I dropped down to peek under it and check out the frame. The frame was so rotted on the right side that the transfer skid plate was hanging down with about an inch of air gap between it and the frame. I would say with the load he was pulling the condition of that frame there was a real safety issue with it!

Sam in IN
05-19-2013 05:17 PM
Hamster
Reinforcement plates for TJ frame rust? pics...

So my TJ has a couple of frame rust spots just in front of both rear wheels. The metal around the holes is maybe half as thick as the rest of the frame. I hammered all around and no soft spots yet. The rest of the frame is solid and clean so I would prefer not to do a total frame swap just yet.

I was thinking of cleaning out the frame and treating it with one of the chassis saver treatments. Question is, could a reinforcement plate be welded on the outside to help strengthen the thin spots in the frame? pics...

Driver side:



Passenger side:


The rest of the frame is clean like this:

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 11:46 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC