|09-01-2013 09:16 PM|
|09-01-2013 09:14 PM|
I'm getting all the stuff rounded up to go full propane as well.
And here are some shots of engine
I made some rear mounts to hold back of motor up during build until trans finds permanent he and crossmember
|09-01-2013 09:10 PM|
|09-01-2013 09:09 PM|
|09-01-2013 09:07 PM|
Could run electric fan and belt driven while allowing room for shroud.
I would set your motor back a tad but keeping an eye on drive line lengths. Ill try and get some pictures for you soon.
|08-27-2013 12:54 AM|
Looking good! I like your paint choice. Your dash looks great too!
Can you provide info about your motor mounts, and perhaps some pics? I bought the Advanced Adapters(weld-in) mounts after reading an article. They spoke highly of them, I am just uncertain where to properly place them. I also am concerned with them being only a cushion style mount vs. the standard GM mount, or even the rubber/poly bushing mounts that people fab.
|08-10-2013 01:35 PM|
|JD95YJ||subscribed.. nice work man|
|08-07-2013 07:53 PM|
|07-31-2013 07:16 PM|
I'm trying to round up the rest of my materials to build cage and get it going.
I gotta get my trans mounted and case then I can finish plumbing. I plan to get fuel cell buttoned up once I cut the floor and drop it 8 inches or so should make enough room for a cooler mount!
|07-31-2013 07:14 PM|
|07-31-2013 01:59 AM|
|jeeperthing||That's a huge difference from when you started. Looking good. It takes a ton of work to get it to where you are at.|
|07-30-2013 11:53 PM|
|BlackTJ98||Nice find. Jealous|
|07-30-2013 09:47 PM|
8 lug d44 I picked up last week. Has the larger stuff. Full width as well
|07-26-2013 07:07 PM|
|Crashzx6r||I'm just gonna use factory gears and shafts and over haul bearings and seals, and build truss and cover|
|07-26-2013 07:06 PM|
|Crashzx6r||Came out of a 79 f250 it's 4.11 with trac lock, full float. Going full width and using same up front.|
|07-24-2013 02:36 PM|
|BlackTJ98||Where did you source your d60 (what model vehicle is it taken from)? Did you have to shorten its width? Going 8 lug?|
|07-24-2013 12:06 PM|
Dana 60 all painted up
|07-22-2013 06:59 AM|
Little progress on clean up work
|07-16-2013 10:16 PM|
|07-16-2013 09:38 PM|
The pace of the build is changed. Gonna be starting cage work and mounting on the 700r4 and np205 then ill be working on the rear d60 I have. Gonna try like hell to find a front d60 in my price range by winter.
Going to also be changing seats to Corbeau Baja ss seats and 5 points. The cage will be pretty involved so ill try to do step by step.
I will be using 1 3/4 .120 wall Dom tubing
|07-04-2013 09:26 AM|
|06-30-2013 08:45 PM|
|06-30-2013 04:16 PM|
|06-30-2013 04:14 PM|
|06-30-2013 04:14 PM|
|Crashzx6r||Alright I've got some new parts in. New griffin radiator, and materials to build my harness and plumb fuel cell. But as I've had more idle time I've decided to just go ahead and do one tons. Gonna wait a whole to 4 link and run kings. I have also decided to run Corbeau Baja ss seats front and a rear bench so everyone can be safe and comfy..|
|06-20-2013 11:23 PM|
|kywaterman||hahaha yeahhh... completely different I agree|
|06-20-2013 10:38 PM|
|Crashzx6r||And...... I know this isn't pirate but the description of the build thread seemed like there would be builds here not sticker and cb installs. I was there once but I didn't start build threads for them.... Smh|
|06-20-2013 09:46 PM|
|Crashzx6r||Freightliners m2 I work for a modification company we do everything from drop frames as pictures to dual drive conversions and fleet service. And thanks! I'm getting more parts rounded up now for it.|
|06-18-2013 11:17 PM|
|kywaterman||looks like its coming along nicley, what kind of truck is that?|
|06-18-2013 05:29 AM|
Been busy at work lately..
|This thread has more than 30 replies. Click here to review the whole thread.|