Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > Backspacing question

Join Wrangler Forum Today


Thread: Backspacing question Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-25-2013 01:07 PM
ameration OK, I'm thinking for going with the Zone 3" Lift with Nitro shocks and was sold by the seller that I would need wheels with 4.5 or less of backspacing. So if this is the case, then I need to get spacers if I want to use the Pro Comp 7031's (4.75 backspacing), correct?

Thanks.
05-24-2013 10:43 PM
BeyondYourFrontDoor It is actually the tire width that you need to consider... not the lift. If you are going to run 315/70s/17 (12.5 wide), then you need at least 5.25" backspacing for clearance. Factory is 6.5", so the typical 1.5" spacer gives you 5" with factory wheels and you are good to go.

If you go with the 4.75" backspacing wheels you are just going to end up with a Jeep that has a 1/2 inch wider stance than spacers... and going to 4.5" would again give you another 1/2 of track... and the ability to run an even wider tire if that is what you wanted.
05-24-2013 10:28 PM
New Jeep I am running Pro Comp 17 inch wheels with the 4.75 back spacing. I have a 3.5 inch lift and 35x12.5 wheels. No problems. AEV runs wheels that are a little over 5 inches of back space and that works too. The 4.5 inch or less may be an old rule of thumb. No worries, you will be fine.
05-24-2013 08:53 AM
chuckr I have the Rugged Ridge wheels which are 17x9 with a 4.75 BS that I'm running with an RK 2.5". I don't use spacers and I have no rubbing issues. RK lifts always give more height than advertised, and I ended up with about 3 ~ 3.5".
Hope that helps....
05-24-2013 08:46 AM
ameration
Backspacing question

I have been told that almost any lift over 2.5" requires a wheel with 4.5 or less of backspacing. I am looking at getting a set of the Pro Comp 7031's in 17" which have a backspacing of 4.75. So if I am thinking correctly, I will need to get wheel spacers to use this wheel on a lift that is over 2.5" or no spacers if I go with a 2.5" lift, correct?

Thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 06:28 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC