Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Body mounts - when to ditch them

Join Wrangler Forum Today


Thread: Body mounts - when to ditch them Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-31-2009 08:53 PM
buckshot500 For the broken bolts, first try drilling them. Center punch your hole dead center in the bolt.
Use a small drill, with light pressure first then slowly increase the drill size. When you have almost reached the threads, use an easy-out to remove the rest. If you can get to the area above the nut, you could maybe use Vise-grips to turn them through.
05-31-2009 08:02 PM
1992wranglersahara Thanks... I'll see what's up when I get to the point of reinstalling the body. I am probably about two weeks away from that (famous last words). My big issue now is the motor mounts!
05-31-2009 07:57 PM
dooder
Quote:
Originally Posted by 1992wranglersahara View Post

Also, that kit doesn't include bolts, so I'll have to get the bolts from them seperately.

The rear two bolts broke off in there, so I guess I am going to drill them out and tap it. Is that the easiest solution?
you could get the 1" lift that comes with bolts Daystar/Four Real Steel KJ04505BK - Daystar 1" Poly Body Lift in Black for 87-95 Jeep Wrangler YJ - Quadratec .

look up a few posts what buckshot posted about drilling and soaking. you might be a bit beyond but still have to remove broken bolts.
05-31-2009 07:43 PM
1992wranglersahara Thanks everybody... I appreciate it. Now, with the Quadratec body mount kit - will that include ALL eleven mounts I need. There is eleven, correct? Four on each side, two in the back and the mount for the nose piece... eleven total?

Also, that kit doesn't include bolts, so I'll have to get the bolts from them seperately.

The rear two bolts broke off in there, so I guess I am going to drill them out and tap it. Is that the easiest solution?
05-31-2009 06:52 AM
minderbinder3 I don't know about all of the kits but on some if you order a 3" body lift then the spacers will be 3" long and they intend for you to place them on top of the original ones. So if you toss the old ones then you are losing 1" from the stock height.
05-31-2009 05:52 AM
dooder
Quote:
Originally Posted by minderbinder3 View Post
but remember if you do that then a 2" body lift will only give 1".
i didnt know that either. i like buckshot thought the lift completely replaces mounts.
05-31-2009 05:37 AM
buckshot500
Quote:
Originally Posted by minderbinder3 View Post
Change the body mounts while you have the tub off. Take my word for it some of the original ones look alright until you go to remove them and they fall apart. Try to get a kit that comes with new bolts and you will be glad when the time comes. Now is the time to decide how much lift you want. You should be able to throw the old ones away and just use the new ones, but remember if you do that then a 2" body lift will only give 1".
I never new that, always thought body lifts completely replaced the stock ones.

Thanks I haven't done mine yet, so I'll keep that in mind.
05-30-2009 10:23 PM
minderbinder3 Change the body mounts while you have the tub off. Take my word for it some of the original ones look alright until you go to remove them and they fall apart. Try to get a kit that comes with new bolts and you will be glad when the time comes. Now is the time to decide how much lift you want. You should be able to throw the old ones away and just use the new ones, but remember if you do that then a 2" body lift will only give 1".
05-30-2009 10:03 PM
buckshot500 I agree on changing them while you have it apart. If the body mounts still haven't been removed yet, there is something you need to know.

Depending on what climates your jeep has seen, (IE; salt belt/ beach cruiser) you have to be really careful removing the stock bolts. If you want to do it right, you should drill a 1/8" hole above each mount, & spray some PB blaster in the weird nuts which are spot welded to the tub.

I have done much research on the subject, & this drilling of some small holes is much easier than chopping a 4" square above each body mount & re-welding the nuts back to the tub!
This procedure is also recommended for the bolts that hold the skid plate on. Only you drill the holes in the side of the frame rails, about 2" up from the lower edge of the frame rail.

Do a board search here, & at jeepforum.com for "broken body mount bolt".
One of these two boards has a post with pic locations of all the holes that need to be drilled. Soak them with blaster for like two weeks, & keep your fingers crossed!
05-30-2009 08:12 PM
jgwalt I did this last year. spray all the bolts as much as you can before you remove them. Although this helps for removal, something will probably give you trouble along the way. I had two bolts break. Best of luck to you!
05-30-2009 08:00 PM
dooder install a new set
Energy Suspension 2-4105G - Energy Suspension Body Cab Mount Set in Black for 87-95 Jeep Wrangler YJ - Quadratec

or in red
Energy Suspension 2-4105R - Energy Suspension Body Cab Mount Set in Red for 87-95 Jeep Wrangler YJ - Quadratec

check here for more
Jeep Body Mounts & Lifts - Quadratec
05-30-2009 07:47 PM
1992wranglersahara
Body mounts - when to ditch them

Hey all -

I am continuing to move forward with my chassis swap due to extreme rot.

The 11 body mounts are what I am stopping to ask about. Before I go laying the body down on these old ones, should I be replacing them? As I said, the old chassis was littered with rot... half of these body mounts look okay, but the other half are not so grand. The rubber bushings have rust embedded in them and the metal sleeves have rust on them, as well. Also, many of the underside bushings rotted away - I have only two left.

Should I be looking at buying a whole new set? If so, should I be looking at a two inch lift kit and kill two birds with one stone? I NEED TO MAKE SURE that I get everything that I need to mount the body back. I really don't want to buy a semi-complete set - only to find out that I have to buy more stuff to mount the body.

If someone has experience in replacing all that stuff and would tell me my best course of action - and what NOT to forget - I would be very appreciative.

As always, this forum is the best. When I get this swap done, I will hopefully be able to share some advice, rather than just ask for it.

Thanks -

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 10:59 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC