|02-14-2014 07:31 AM|
|jkdave1||Does anyone have the 43.00.13 FW iso anywhere? I can't seem to find this update anywhere, been looking for a few days. To clarify i'm not looking for the 50.00.07, only the 43.00.13.|
|01-22-2014 10:29 AM|
|01-10-2014 03:45 PM|
|BLK2012||Thanks for this update.....much easier on the eyes than the update I got that started this thread...|
|01-08-2014 11:17 PM|
|BubbaEinstein||Any updates for the 730?|
|01-06-2014 04:13 PM|
Just upgraded also ...following this thread..burnt the cdr and now I'm at 50.00.07
Thanks to all who posted and provided necessary materials.
|01-02-2014 02:14 PM|
Just finished upgrading my 1202 Jeep Wrangler 430n RHB radio from 33.00.41 to 50.00.07 using the ISO and PDF posted in this thread with zero problems. Made sure the key was in the ON position and was patient. Thanks everyone!!
|12-22-2013 03:42 PM|
question on upgrade
Can you do the upgrade on a flash drive or does it have to be burned to a cd?
I put it on a flashdrive and all it says is no files on usb when I put it in the jeep
|12-10-2013 06:29 PM|
|Mack207||So is there any way to change the "Yellow Theme" on the 50.00.07 to another color?|
|12-09-2013 11:24 PM|
|12-09-2013 09:27 PM|
|12-08-2013 11:17 PM|
|12-08-2013 10:17 PM|
|bouche03||Anyone have problems with their RBZ 430 not recognizing their iPhone via the USB port in the front of the head unit? It charges my phone but will not let me stream music while plugged in...HELP!|
|11-05-2013 06:40 PM|
|JedFromAZ||Well I got my 430N replaced under warranty yesterday. Good news is that the maps and icons are more vivid. Bad news is that it came with the Jeep ghost image brand new from the factory. So much for Chrysler's QC. The stereo tech guy said that they should have a newer update disk in next week.|
|10-13-2013 04:57 PM|
|10-13-2013 09:38 AM|
|10-04-2013 10:46 AM|
|Navydave73||I just performed the update. Thanks to the member that reliables the download thread for the .iso file. I followed the PDF instructions exactly and it worked great. No update to the maps though. In fact my radio just hit me up to buy the new map package this morning. Thanks everyone for help and recommendations. I went from 30.xx to 50.00.07. Thanks again|
|10-03-2013 06:14 AM|
I had the same problem but my problem was because I had a mygig lockpick. I disconnected the lockpick and reconnected the radio to the stock wiring and it solved my problem. Once the radio restarted I was able to reconnect my lockpick.
|10-02-2013 06:38 AM|
Have yo tried disconnecting the battery for about 20 minutes? This sometimes will let the radio reboot. If it's still under warranty, take it back to the dealer.
|10-01-2013 09:54 PM|
|sean.busse||Hey guys, I think I really screwed up. I downloaded the update for the RHB for my father in law and the RBZ update for myself. In some sort of confusion I ran the wrong update in my RBZ and now my uconnect is stuck on the start screen no matter what I do...anybody have any ideas?|
|09-26-2013 07:10 PM|
|09-24-2013 06:24 AM|
Chrysler does not have a Gracenote update available and most likely won't. They used to offer an update disc but they discontinued it due to lack of sales.
|09-23-2013 01:54 PM|
hi---anyone know where I can download the latest Gracenotes? last one i have is BA1
|09-16-2013 10:27 AM|
For those of you with 430/430N radios with application version 23.04.41, who have been sitting on the fence concerning this update, do it.
I just downloaded the update using the link provided by "hgmeganet" and updated my 2011 430N. It change the background from blue/white to the preferred black/green, updated the SIRIUS radio to show the station art work. I did get the "PND did not update" message, which left my nav screen looking the way it did before the update, which is OK by me as I wasn't happy with the way the graphics looked with the black/green background.
All in all, a easy update if you follow the instructions per the Service Bulletin 08-061-13
|09-16-2013 07:05 AM|
When a call is made using Uconnect and other BT car kits, the car kit will tell the phone to place a call, the phone needs to respond back to the car kit "ok" and it starts to place the call, the car kit will then ask the phone if the call is active, the phone needs to respond back with either "active or not active", if the phone doesn't respond correctly or not at all then the car kit will say "call completed" and then tell the radio to leave the hands free mode and go back to the radio.
It is possible for the phone to incorrectly respond and the call is still active on the phone itself.
The phone also is telling the car kit about the battery and signal strength with a range from 0-5 (where 5 is the highest), I have seen where a phone has weak service and sends a 0 but it shows 1 bar. This will also cause the car kit to say "call completed" but possibly still be active (barely) on the phone. I have also seen an AT&T phone do this during a tower hand off.
@ Bad_Dog, when Uconnect says "call completed" is the call still active on the phone itself? I have seen where the call is active on the phone still after the "call completed" prompt and then while it is still active on the phone, press the Uconnect button and place a call and it goes thru. This because with the 2nd call, when Uconnect asks the phone about the call, the phone now responds that there's a call on hold and 1 outgoing active call.
So see there's a lot going on during a call or trying to place a call and each device must communicate correctly or the system won't work correctly. It's not a matter of "she's not too smart", sometimes an issue is with the phone and not the car kit.
|09-16-2013 06:42 AM|
Correct, it's limited by the it's HW.
|09-16-2013 06:36 AM|
just a couple notes here, ok.
1) As a 25 year (+) automotive electrical tech, I personally always have the engine running or have the vehicle on a battery charger during the update process. The reason for this is because any power interruptions during the process is capable of damaging the module or locking it up. So even though the instructions say "key on but motor not running" I suggest that the vehicle is in a well ventilated area and the engine running. I think that their wording is mostly to keep people from killing themself if they try to perform the update inside a garage with the engine running.
2) Chrysler probably doesn't want to pay their techs to update vehicles older than 2012. I have (as well as others) done this update on a 2011 vehicle with SW version 23.04.33 and it will work on SW versions higher than the 23.04.33 but not lower that it.
|09-15-2013 07:47 PM|
Half of an update?
Hey all, brand new to the forum, joined to reply to this thread. I downloaded and burned the .iso and the update seemed to finish properly but I have no images. the color scheme changed from blue to the black and the SW version changed but there are no brand logos or background colors like all the pictures I have seen posted. Anybody else run into this? This is an RBZ radio in a 2012 rm 3500 if it matters. The radio used to show the ram head logo and whatnot and now just a blank screen aside form the text.
|09-14-2013 02:20 PM|
|Lucy Brown||I spoke with a uconnect rep yesterday. She transferred me over to a rep that was specializing in this issue. He told me that they are mailing out new disks and that I should be getting one soon. He advised if I didn't want to wait to go to my dealer as they should have the update disk already and they could do the update for me at the dealer. Big about face from the last time I spoke with them and they flat out lied and said the old blue screen was normal to see after the update.|
|09-14-2013 02:00 PM|
|Jeepula||anyone doing this themselves its not just a burn to disc. make sure you burn the iso image right and also follow the PDF instructions. In the instructions it says turn on but not running and turn radio off first etc. RBZ and RHB also doesnt mention any jeeps before 2012.|
|09-14-2013 06:57 AM|
|This thread has more than 30 replies. Click here to review the whole thread.|