|06-13-2013 10:05 AM|
|freeskier||There are a number of JK owners with over 30k miles on these joints and no issues.|
|06-13-2013 09:58 AM|
|NJO||I won't run anything but MC DF joints. I've had mine in for about 6 months now. Fantastic ride quality on road, and off road flex is effortless. Quite a few people in my club have switched out their JJ's for them or are going to in the very near future. Best all around joints on the market. Durability is a non issue too IMO, they have been out for a few years now, I really haven't seen any complaints, nothing but positive reviews. Super easy to field service too...no special tools needed....a single joint can be swapped out in 5 minutes flat.|
|06-12-2013 07:06 PM|
Yes, the salt and cold can trash bushings etc fast up here! The cold can make 'em hard and seperate/unbond then the salt gets in and really buggers stuff up
Good to hear no issues so far. I'm saving for a set and some other items
|06-12-2013 06:48 PM|
We have several customer up in Canada where they use a liquid salt on the rode and have had no reported issues. This is coming from guys that can kill any joint purely because of pitting. We are looking for the long term feedback.
|06-11-2013 07:00 PM|
|IcarusLSC||Thanks matsonian, and in the salt etc how are they lasting?|
|06-11-2013 06:44 PM|
|Gary2||I've been running them since last September . The have been a great addition to my TJ . I have the double adjustable aluminum Savvy arms that at one time had Johnny Joints but I did not care for the ride with all JJs so I experimented with a couple sets of DF joints and soon after replace all my JJs. I have since sold my upper JJs and the guts to all the lowers are in a bag on a shelf where I keep spare parts . I have nothing negative to say about the Mc joints and I have a smooth ride again|
|06-11-2013 06:40 PM|
|06-11-2013 06:28 PM|
|06-11-2013 05:58 PM|
|kjeeper10||Check out the vender threads on here. MC is listed.|
|06-11-2013 05:43 PM|
|IcarusLSC||How are these joints for a mainly daily driver, bit of a weekend toy up here in the salt/snow too?|
|06-11-2013 12:06 PM|
|06-11-2013 11:37 AM|
As for reliability... we would not use them on our products unless we were confident in their performance.
|06-11-2013 11:20 AM|
Not sure if I can post this link, but here you go.
??? For the metal cloak arms owners - JKowners.com : Jeep Wrangler JK Forum
|06-11-2013 10:19 AM|
|06-11-2013 10:12 AM|
However, I do need to comment on this statement just so there is no confusion.
Metalcloak did not have a car at KOH. I personally own the car and it is not sponsored at all by Metalcloak.
When a car is fully built around heim joints, like 4576 was when I bought it, it's not a smart idea to just throw another joint in, otherwise I would have happily run them.
When and if Metalcloak decides to get into racing and build a car for the EMC at KOH, you can bet it will be running our full suspension offerings.
Oh... and by the way, the car WAS running a single Duroflex Joint... as an engine mount.
Thanks again for all the great feedback!
|06-01-2013 11:33 PM|
|06-01-2013 11:20 PM|
|06-01-2013 11:12 PM|
|06-01-2013 11:10 PM|
|06-01-2013 11:10 PM|
Not like it can't be undone if I don't like them down the road. Thanks guys
|06-01-2013 11:09 PM|
|06-01-2013 11:03 PM|
|06-01-2013 11:01 PM|
I personally don't like them for many reasons. I predict durability issues later down the road similar to the stock bushings. Hell, Metalcloak didn't even run their joint in their car at KOH this year.
As far as the review above, I wouldn't take it too seriously durability wise. One wheeling trip isn't enough to determine long term durability. There's a good thread on JK Owners about this, after I read it I stuck with my JJ's.
|06-01-2013 10:52 PM|
|Patrick H||How the Metalcloak Duroflex bushing stacks up - JeepForum.com|
|06-01-2013 10:34 PM|
Your thoughts on Metalcloak Duroflex joints?
Hey again everyone, so I am looking at building (assembling) some control arms for my TJ. I am very interested in Metalcloaks Duroflex joints but I haven't heard much review about them.
Does anyone run these? What are your thoughts?
My plan was to take MC Duroflex joints and use the Savvy aluminum CA arms to make a nice set.