Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Oil pressure gauge

Join Wrangler Forum Today


Thread: Oil pressure gauge Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-12-2013 05:05 PM
jkp They make a special socket for them that has a slot for the wiring harness. Otherwise, you can cut the wires and use a deep well socket if you have one deep enough.
06-12-2013 10:09 AM
jeeps4u2nv88 Not what I wanted to hear but at least it is a inexpensive part none the less. Any tips on getting the old sensor out? Tried an adjustable wrench and I just couldn't get the wrench in a good position to get a grip on it.
06-12-2013 10:04 AM
Jerry Bransford The sender could look brand-new and still be bad if it was a cheapy from China as Atthehop talked about above. I use a lot of aftermarket parts on my TJ but for sensors and other critical parts, I try to use nothing but OE Mopar replacements. I replaced my son's oil pressure sender 3X on a Sunday before I finally got one from Autozone that worked properly. One even read backwards. That wouldn't have happened if it had been any other day of the week when I could have instead picked up a sender from the dealer.
06-12-2013 09:28 AM
jeeps4u2nv88 So I took a look at the sending unit last night and the unit looks brand new. PO may have replaced it and not said anything. I took the wire connector off and attempted to take the unit off but couldn't get a wrench on the sending unit. Didn't have much time to mess with it so i just reconnected the wire connector. Just for giggles I started up the Jeep to see if just messing with the connector fix my problem and sure enough the oil pressure gauge goes right up and there is no appearance of the "check gauge" light. YA!! At idle I have about 10-13 and at about 2000 rpm I have between 20-30. I did some research and that sounds normal.

But.... there is always a but, on my way to work this morning the oil pressure gauge went back to reading 10 or below at 2000 rpm. The engine was running fine and there was nothing abnormal about my drive.

Question is, even tho the sending unit could be newer could it still go bad that quick?

also why would it work then stop working?

Thanks
06-11-2013 10:04 AM
The Newbie I ha that same issue on my jeep I replace the sensor bit it still was doing it. I found out that it was actually the oil pump after I pulled someone out and started having a rod knock
06-11-2013 08:55 AM
jeeps4u2nv88 Atthehop: Thanks will do. I searched the topic right after I posted, should have done that first, and found your other post saying the same thing.

Wattapunk: My picture is of my 1998 YJ but the vehicle in question is a 1998 TJ. Sorry about that, should have mentioned that.

Thanks though!!
06-11-2013 08:47 AM
Wattapunk x2 on the sending unit. Just FYI, may help if you post in the YJ section.
06-11-2013 08:44 AM
Atthehop Most of us have had to change the oil sending switch. I recommend buying one from the dealer since the stuff in auto parts stores are from china and usually junk.
06-11-2013 08:15 AM
jeeps4u2nv88
Oil pressure gauge

OK, so my oil pressure gauge has been acting up and I have no idea what is causing it. First of all, the oil level is normal and clean and the Jeep receives regular maintenance in all ways. The problem is this, when you start the Jeep everything starts up fine but the "check gauges" light comes up. The oil pressure gauge doesn't register anything. If I rev the engine the "check gauges" light goes off and the oil pressure gauge goes up but to a very low pressure reading. I have pointed it out to a mechanic and they said everything with the engine is working fine. This makes me think its the sending unit but have no idea where it is or what to check. Any suggestions on what to do to fix it or trouble shoot it? Anyone have the same problem?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 01:46 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC