|06-19-2013 06:41 PM|
|06-19-2013 05:21 AM|
|eugenesonrisa||The jeep seems to be much less wobbly and have less drift back and forth while I drive straight. This of course is compared to the original trackbar that had been set 1/2" to the right to accommodate the lift and had a wallowed out axle side hole.|
|06-18-2013 10:05 AM|
|Arch Stanton||How does your Jeep feel on the road with the new MC TB? Thanks!|
|06-16-2013 10:11 PM|
|IcarusLSC||I'd love to get one of those, but don't think the heim joint will last in the salt and crap we get|
|06-16-2013 01:46 AM|
|06-16-2013 01:36 AM|
|06-15-2013 07:19 PM|
|06-15-2013 06:35 PM|
|BrutusTheTJ01||I was back and forth between the MC rear track bar or a Currie, so I had to really weigh the options with the type of wheeling I will be doing with my time left here in the UK, and the direction I want to take my build. The price was a plus, but I really like that the rear MC tbar uses the factory mount instead of any type of relocation bracket.|
|06-15-2013 06:13 PM|
|eugenesonrisa||Nice to hear. That's one of the next issues I need to address. I inherited the jeep from my parents and unfortunately a lot of things were done at a shop several years ago and I'm trying to rectify a lot of problems that were caused by a poor setup and a lot of years.|
|06-15-2013 04:22 PM|
|BrutusTheTJ01||Looks good. I just installed the MC rear track bar yesterday..much easier is it uses the stock hardware and requires no drilling. I haven't had a chance to test mine out on the trail, but I don't for-see having any issues with either the front or the rear.|
|06-15-2013 03:46 PM|
1/2" axle side
5/8" frame side
|06-15-2013 02:58 PM|
|rdock31||What size hole did you have to drill the stock hole out to?|
|06-15-2013 02:26 PM|
Side by side original with 130,000 miles on it:
Frame side attachment:
Axle side... Need to fill the relocation hole:
After all was said and done it was very easy and straightforward. Got burned by some of the metal shavings as they came out and had the drill buck a few times when it would catch. When I was done and went on a little drive to check it out, the steering wheel had rotated to the left.
|06-13-2013 08:31 PM|
|eugenesonrisa||I'll have to look out for that. Haha. Thanks for the advice!|
|06-13-2013 04:24 PM|
|BrutusTheTJ01||The axle side bracket is 1/2in hole, the frame side is a 5/8in hole. I would suggest getting as much room as you can (removing tires, coils, etc.) when you drill the hole, or the bit will catch and the drill will smack you in the face (found out the hard way). I had more problems removing my stock TB than anything. the MC bar installation was a breeze.|
|06-13-2013 03:11 PM|
|06-13-2013 02:49 PM|
|06-13-2013 02:06 PM|
|06-13-2013 01:18 PM|
Doesn't the front TB require a 5/8" hole drilled out on the frame side as well?
The MC front trackbar due to the frame side heim and smart bends gives to most clearance of any aftermarket TB and requires no additional bumpstopping over stock which is nice. Just make sure you have at least 2" lift if you want the axle to center properly on the frame. Good pickup.
|06-13-2013 01:03 PM|
|eugenesonrisa||"Bump" for any thoughts|
|06-12-2013 07:06 PM|
|eugenesonrisa||Will do. Should be going down this weekend.|
|06-12-2013 06:50 PM|
|06-12-2013 06:40 PM|
It is the front. Haven't unwrapped it all the way yet but I can say that it is heavy. Probably about 25lbs. Not that that actually means anything... Was going to wait to unwrap until I'm going to put it place so nothing stupid happens to it.
|06-12-2013 06:33 PM|
|Arch Stanton||Is this the front or rear? What's your impression of the track bar? Do you have any pics?|
|06-12-2013 06:16 PM|
Replacing relocated stock trackbar with metalcloak
So I currently have a regular trackbar that has been moved over with a new hole drilled. The hole has wallowed out a little and I'm replacing it with an adjustable trackbar. I ended up going with the metalcloak trackbar so I will have to drill out the axle side hole to 1/2"
I'm guessing the space between the larger hole and the previous hole from relocation will be small, does anyone know if this will be a problem?
Also, any clue what to torque the new trackbar to?