Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > yj clutch master and slave replacement

Join Wrangler Forum Today


Thread: yj clutch master and slave replacement Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-15-2013 10:26 AM
JACK3D I replaced mine with a Luk clutch kit back in February. Have had no problems out of it. Ordered it from partsgeek.com. It was right at $100 free shipping.
06-15-2013 09:17 AM
gutter1546 And quadratec is gonna refund me
06-15-2013 09:16 AM
gutter1546 Thanks guys napa part on the way
06-14-2013 12:08 PM
Surfinglbi23 Agreed with above, did mine through Rock Auto and has worked perfectly since September.
06-14-2013 11:56 AM
jokerchief462 Pre 94??? Internal slave cylinder I assume no info in profile. Either way when you install the internal you have to make sure it is positioned on the alignment pin on the trans front bearing retainer there is apin there. Next you have to install the 2 o-rings carefully and then insert the line and install the retaining clip. Leave the plastic strap on the piston it will break free first actuation of the clutch. Once assembled be careful how you yank on the slave cylinder input line you can upset the seal of the o-rings at the input spot of the slave cylinder.

External slave is no issue and they seem to all be plastic now. Pretty straightforward install 2 bolts tightened simultaneously with the plastic strap on until first activation.

Bleeding the internal is like doing old fashioned brakes through the bleed nipple. External some new ones don't come with a traditional bleed nipple. You will find a set screw which will let you gravity bleed for s start. If it didn't say in the instructions how to bleed the new externals here is a quick shot and yes it is real and works just sounds stupid.

Before you install the external slave without a bleed nipple, like I said use the set screw to initially gravity bleed the cylinder and tighten. With cap off masetr and full take the slave cylinder in hand and actuate the piston 20 cycles while pointing the piston at the ground. The air will travel back up into the master. Check fluid level and repeat. When finished service the master and install the slave cylinder with the two bolts and the plastic strap still iinstalled.

It seems to be hard to find good quality parts now a days but when you find a place that carries them keep going back and cheap parts aren't always the best.

Try Rock auto at rockauto.com I have had real good luck with their parts and the prices are always good IMHO.
06-14-2013 11:29 AM
chrysler-tech-420 Ensure that u are properly installing the slave retainer and that ur slave is seated flush on the front bearing retainer. Are u running stock engine trans? If ur stock and installing slave properly id say try a different parts store for ur next slave. Ive had batches of parts such as waterpumps on the 318 I went through 4 in a month before going to a different store and now ive been running that one three years. Batches sit in the warehouse and seal degrade making the entire stock warranty issues.
06-14-2013 08:25 AM
gutter1546
yj clutch master and slave replacement

I recently ordered a crown automotive master and slave clutch assembly worked great for about a month until the plastic slave cylinder blew out so I contacted quadratec and they sent me a replacement part through crown automotive which took 5 weeks to come inthe replacement worked great for about a month until the master blew on the replacement . Has anyone else had anything similar happen ? Could there be an underlying cause or did I just get two faulty parts?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 08:35 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC