Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Home-made Hard-top hoist

Join Wrangler Forum Today


Thread: Home-made Hard-top hoist Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-18-2013 12:25 AM
Tyr4nt Awesome! Thanks guys!

I bought a hand crank winch from Harbor Freight and found a complete winching strap from a flat bed tractor trailer (stopped the car on the interstate... wife was freaking out thinking we got pulled over lol). I plan on making the hoist this weekend (if time permits).
06-17-2013 06:43 PM
BadOleRoss Went home and did some quick measuring! I built a "T" shaped frame! Looking at the "T" it's 48" tall by 60" wide. Once assembled and laying on top of the Jeep with the bottom of the "T" at the rear wind, there are 2 "L" shaped hooks that slide in between the back of the hard top and the opened rear window that catch the back of the hardtop. On each side I have eye bolts that I run a tie down between to hold the front half of the top up. The hoist is attached to an eye bolt that is 18" off the rear of the hardtop. The side eyebolts are 58.5" inches apart.
06-17-2013 03:50 PM
mikemounlio make your T frame with hooks and all. Either make a loop in your cable or make the cable tie in to the T frame adjustable. Not all tops are gonna be the same. You will need some fine tuning. Then just give it a slow pull and see the reaction. If you see the front or back start to tilt you know you are not at the balance point. Adjust till you feel its the best for your top and secure in place.

For the record most ratchet straps can go in reverse whilt under load. My two strap to the celing front to back of the jeep is just as fast as the hoist. same prep time same operation for the most part.
06-17-2013 03:05 PM
BadOleRoss I made my own lift using a manual winch and a frame made of out 2x6s and some hooks I had sitting around. I will try to remember to get those measurements for you tonight. If I forget, send me a PM and remind me.
06-17-2013 02:28 PM
chemicaljeep I put d-rings in garageceiling joist and tied ropes to it. pull it up all the time by myself. also put back on by myself. take 10 min.
06-15-2013 10:50 PM
Tyr4nt sok - If anyone responds to us I'll let you know. Otherwise, next weekend I'm going to mock it up myself and I'll make a pic tutorial and send you measurements.
06-15-2013 02:36 PM
sok i would to like to know as well going to take top off for first time with straps an my deer hoist
06-14-2013 11:07 PM
Tyr4nt
Home-made Hard-top hoist

Hey hard-top hoist owners,

Could someone do me a favor? I'm trying to find the center of gravity for the hard-top so that I can make my own hand crank winch hoist.

I need to know two measurements.
1) Measurement from the host to the edge of the rear window
2) Measurement from the host to the nearest edge

Thanks!!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:49 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC