Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Death Wobble

Join Wrangler Forum Today


Thread: Death Wobble Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-25-2013 10:36 PM
KLP
Bushings?

I just bought new bushings (PVC) and not rubber. About $15 I think, special order. Also bought a pickle fork to get the trackbar off. Def. worth the $10 for it. The old ones were egged out and new ones cured my DW.
06-25-2013 09:31 PM
Hockey Ref Is it possible to change the track rod bushings, or must the entire unit be replaced?
06-25-2013 07:24 PM
Kodywitha__K ^^^^^^That>
06-25-2013 07:01 PM
Pink_Percy Attachment 265564
06-25-2013 04:08 PM
Sccrbrg
Quote:
Originally Posted by Kodywitha__K View Post
That's what we're going to do. I'm sure we'll be able to figure it out!
Whatever you do, i would get it fixed before you drive it anymore.

After a couple of DW incidents my steering column had to be repaired (and things around it) because the shaking had broken factory welds.

Not to mention my jeep was nearly impossible to stop or control during a DW strike.
06-25-2013 09:54 AM
Kodywitha__K That's what we're going to do. I'm sure we'll be able to figure it out!
06-22-2013 02:00 PM
PStov98TJ You can do this stuff yourself. Go get some tools, they'll be cheaper than labor costs, and do it yourself. I'm only 20 and I do 99% of all the work done on my jeep. And no my dad isn't some master mechanic (to be honest, he's not much of one at all). Just do some research, look at write-ups, and watch videos and have a little faith in yourself.
06-22-2013 01:10 PM
Kodywitha__K
Figured it out....

Well let's see where to begin. Well on the bright side we figured it out, the downside is apparently the guy that I bought the jeep from just rigged the steering system to, and I quote, "work." The tie rod, which is from a RAM truck we believe was mounted to the same spot the drag link is because it was too long to fit where it was actually supposed to go. Then the steering stabilizer was welded, I mean WELDED to the drag link because there was nowhere to bolt it in. Now I'm no expert on vehicle repairs, but I'm pretty sure that if the part is the correct part then it should fit where it's supposed to fit. Sorry about the rant...I'm just a little angry that I bought this jeep from an authorized dealer and he ensured that he had the whole jeep "inspected" and now it's going to cost me a fortune because as I said, I'm and 18 year old with no experience in vehicle repairs........
06-19-2013 09:48 AM
Jerry Bransford Three things... 1) The tie rod and drag link are mounted on ball joints so they are supposed to have rotational play. They just should not have any side-to-side play. 2) DW is very commonly caused by nothing more than an imperfectly balanced tire. Not many tire shops get tires balanced well enough for a TJ & the bigger the tires, the more important perfect tire balance becomes. 3) Once triggered by something like an out of balance tire, a loose track bar at its passenger-side mount can allow the DW to fully develop. Have someone turn the steering back & forth (tires on the ground) while you watch the track bar's passenger-side mount for unwanted side-to-side movement... there should be zero. Check the tie rod & drag link for side-to-side slop too once you've checked the track bar.
06-19-2013 09:41 AM
Water Dog
Quote:
Originally Posted by Spitse View Post
Check the stabilizer especially if the DW started over night kind of thing.
Just FYI...the steering stabilizer will only help to mask a problem that is already there. It, in and of itself is not the "cause" of death wobble. If everything else is right, you should be able to go without a stabilizer and have no DW. As has been mentioned, check the alignment, track bar bushings, and tie rod ends first, then ball joints, ca bushings etc.
06-19-2013 06:50 AM
Spitse My experience with the dreaded DW is not in a jeep as I am new to this world, but another Chrysler product a ram 3500 diesel. Of the 2 times I have had to have it addressed professionally, it was first the ball joints. Even thought they were tight, they had flat spots in then that allowed the play under motion. The second time was the steering stabilizer. The piston inside blew and so it did nothing.

Check the stabilizer especially if the DW started over night kind of thing.
06-19-2013 06:39 AM
Kodywitha__K
Thanks

All right! Thanks everyone, I'll take a look and see, and if I run into some other stuff that doesn't seem right, you know where I'll be!
06-18-2013 09:17 PM
Newly installed long arm
Quote:
Originally Posted by Kodywitha__K View Post
Hi all,

I just recently began experiencing the blessing of a gift that we call the death wobble........but I'm only an 18 year old kid without much experience when it comes to vehicle repair. I was reading up on the wobble and I took a look front end to check and see if things were loose and if there was any play in the suspension system. I noticed that (what I think is) the drag link (which is connected to the pittman arm) has the ability to rotate, quite a bit actually. Everything else looked like it was in pretty good shape and I made sure everything was tightened down. Can someone please help me out? Do you think that the drag link being able to rotate is causing this?

And yes I am positive that this is the death wobble. This is no small vibration, the wheels look like they are gunna fly right off when it happens.

Thank you!
My experience is that it usually something to do with the track bar it seems tight but something is lose get somebody to watch each end while u turn the wheel slowly back and forth and u dont haft to turn it far just a little u do not need to start the jeep just unlock the steering wheel
06-18-2013 09:08 PM
Water Dog The ball joints on the drag link, as well as the rest of the suspension components are supposed to rotate (that is why they use ball joints). The video was good, but also grab on to each component while someone is turning the steering wheel. Sometimes you can feel what you can't pick up visually.
06-18-2013 05:44 PM
TeraFlex Not from us but this should help. Rock Krawler Death Wobble Diagnostic Video - YouTube
06-18-2013 05:31 PM
Kodywitha__K
Death Wobble

Hi all,

I just recently began experiencing the blessing of a gift that we call the death wobble........but I'm only an 18 year old kid without much experience when it comes to vehicle repair. I was reading up on the wobble and I took a look front end to check and see if things were loose and if there was any play in the suspension system. I noticed that (what I think is) the drag link (which is connected to the pittman arm) has the ability to rotate, quite a bit actually. Everything else looked like it was in pretty good shape and I made sure everything was tightened down. Can someone please help me out? Do you think that the drag link being able to rotate is causing this?

And yes I am positive that this is the death wobble. This is no small vibration, the wheels look like they are gunna fly right off when it happens.

Thank you!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 10:23 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC