Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Slip Yoke Replacement

Join Wrangler Forum Today


Thread: Slip Yoke Replacement Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-21-2013 12:19 PM
Jeepfreak94 When running a standard driveshaft(1 joint at each end) the angles at the joints should be equal but opposite with the axle yoke having a little more downward tilt to account for pinion rise when under power. Unequal angles can set up odd harmonic vibrations in the shaft that can and will FUBAR joints, yokes and/or shafts, as you can testify to. Like stated above a transfer case lowering kit will help buy you some extra time until you can afford a SYE kit.
06-19-2013 10:30 PM
Lunabadger My rear axle is rotated up slightly to lessen the angle there. Right now the degree is on the verge to the t-case. What made it snap, though, was just that the u-joint had been in there for several years and it couldn't be greased; it just dried up and snapped.

If it continued as usual, sadly i can plan, i have about 9-10 months before i need to replace it. Hopefully i can get myself a main commuter by then so i can tear my jeep apart and start one of those build threads.
06-18-2013 06:36 PM
4Jeepn does your jeep have a t-case drop of any kind? what about degree shims on the rear axle under the leaf springs.. that might help to buy you some more time between u-joint changes.
06-18-2013 06:00 PM
Redrider94 As long as you took the snap rings out you did good, when you put it back together make sure you put the new snap rings back in.
06-18-2013 05:50 PM
Lunabadger Well, i just ended up pounding out the caps.


Probably not the best method, we'll see how it runs.
06-18-2013 04:19 PM
Lunabadger
Slip Yoke Replacement

Hey, i hate being the guy to just create an account to ask for help, but it's necessary right now.

I drive a '94 YJ. She's equipped with about a 4" lift. Obviously that's been causing problems with my rear end.
A few times, now, the rear yoke in the differential and u-joint have exploded and i've had to replace them.
This time, rather than it popping out the differential, it's chewed up and exploded from my transfer case.
Right now i don't have the funds for a SYE, so i am just trying to replace the yoke itself.
However disassembly of the drive line has been eluding me and i need advice on how to carry out. I will grab some pictures of the affected areas.

What i am looking for is tips on disassembly of the drive line's u-joint, but also reassembly with the new materials. Thanks in advance!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:11 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC