|07-01-2014 10:23 AM|
Finally had a chance to take off the bumper and mount the winch, see the picture below but I think you could drill thru to mount a license plate depending on the location of the holes but it would be awfully tight. I haven't had a problem with not using a front plate but that doesn't mean I won't. I'll probably get a setup to attach it to my fairlead one that flips or is permanently attached rather than the clip-on ones.
|07-01-2014 10:14 AM|
It's been a while but got some updates from the last week... Got the winch all mounted up and replaced all the torx bolts on the bumper. I also replaced the front brakes with centric rotors and EBC Green Stuff pads. The brakes were probably the easiest brake job I've ever done. My floor jack crapped out so I had to use the bottle jack and was done in about an hour from tires up to tires down. Although there are better upgrades for brakes I am very happy compared to what I had. I couldn't have finished sooner no rain was supposed to hit us but we got a hell of a storm less than 2 hours after I finished. No complaints on the rain however. Picture time
|06-16-2014 06:21 AM|
|05-06-2014 08:42 PM|
|Neal5280||Mine are old but I know that they are carbide tipped. As far as brand I would think that most MAJOR brands will be ok, especially for how much use they'll get. 1/2 you'll use again probably but 5/8 may never get used again.|
|05-06-2014 08:36 PM|
|05-06-2014 08:13 PM|
Yep you are right looking at the Jeep frame side on the right axle side on the left. I am too that's the beauty of a forum like this!
|05-06-2014 08:08 PM|
|05-06-2014 08:07 PM|
Thanks! I like it and am going to have fun this summer. By next year about this time I do hope to be on 35s though. Will have to do some axle work before that for sure though. She sure is coming along though.
|05-06-2014 08:03 PM|
You know I'm not sure when I take it off this weekend to re-install the winch I'll take pictures and post up.
|05-06-2014 08:02 PM|
Yep have to do 5/8th on the frame side and 1/2 on the axle side. Use good bits the frame side was quite tough. The thing is stout.
|05-06-2014 02:41 PM|
|NC Bear||that looks good man, I actually think it looks proper with the 33's.|
|05-06-2014 11:06 AM|
|BrutusTheTJ01||Looks good man. Question about the Barnes bumper. Is there enough room between the bumper and the frame to drill two holes to mount a license plate??|
|05-06-2014 09:50 AM|
|GSXRMAN14||Did you have to drill anything for the MC Front Trac Bar? I get mine tomorrow according to my track #.|
|05-06-2014 09:13 AM|
Well finally got to work on her a bit a few weekends ago. Got on the Anti-Rock, Barnes Bumper, 3in BDS front springs, 2in BDS rear springs & MC Track bar on and am loving it. I haven't put the winch back on yet hopefully I will get to that this weekend along with new front pads and rotors. I'm hoping to do my SYE/DS, rear adjustable uppers, Novak cable shifter and UCF Ultra HC Skid in the first few weeks of June. Now some pictures
Anti-Rock (pictures before lift so angle looks a bit high but is perfect now)
MC Track bar
|03-17-2014 02:25 AM|
|Neal5280||Yea I actually like the feeling on road after driving more tonight. Yea they did bolt, lock washer and larger washer for both ends.|
|03-17-2014 01:33 AM|
|BrutusTheTJ01||Antirock is one of my favorite upgrades. Did yours come with the bolt and washer to put on the outside of the arm?? Mine didn't, and last time I was out on the trail, my right side arm fell off.|
|03-16-2014 06:00 PM|
Well, baby steps... Got the bumper painted and installed with the anti rock. Initial impressions are that the bumper is perfect once painted it installed without any issue. The AR took a little longer than I thought but was very straight forward. It is set as short as it'll go and I didn't want to trim the rods because I will be putting 3" springs in it in a few weeks. I will adjust at that point. I don't notice much of a change in street behavior with the AR but took it out into some fields and it was a night and day difference, can't wait to get on a trail but no such luck today...
See it did happen
|03-07-2014 04:32 AM|
Small update and some progress....
I've received the bumper and MML. I am taking my UCF t-case skid in for powder coating tomorrow got a killer deal on it, I was looking at it last week and didn't feel my painting "skills" would produce good coverage on the top side. I should have that back early next week. I am also set to paint my barnes bumper and UCF oil pan skid tomorrow. As long as everything looks good I'll be putting on the bumper and AR on Sunday. If I have time on Sunday I'll also put on the ZJ TR, also need to replace the TRE at the pitman arm and do the toe in adjustment & center the steering wheel. Then if it's decent next week I'll do the springs, MML, MC rear upper adjustable CAs and front MC track bar. Pics to follow hopefully on Sunday afternoon.
|02-19-2014 07:13 AM|
|Neal5280||So finally got the shipping notification from Brown Dog. Hopefully I'll have the MML in hand early next week. Hoping I get the front bumper soon I am waiting on installing my AR until I do the bumper at the same time.|
|02-18-2014 02:36 AM|
Thanks man! I am about half way thru your build and it is awesome so far! It seems like we are taking similar roads
I am excited to get some of this going... Parts pile is crazy right now, I wish I had a garage like yours that would be awesome! Also I'd probably be a lot more tired too!
I look forward to finishing up your build thread.
|02-17-2014 07:47 AM|
I really like the looks of your build. You and I have several similar parts and plans.
I am running BDS 2" coils front and rear with a 3/4" spacer up front. The spacer was to compensate for winch and bumper and it did that just fine. With the 8.8 installed, the back end is probably 1/2" higher.
I think your 3" front coils will do well once you get everything dialed in.
After I finish loading my jeep down with the remaining armor and spare tire, I will see if I need to make coil adjustments.
|02-17-2014 06:37 AM|
So unfortunately I've had to put the 8.8 on hold due to some other financial responsibilities. Damn responsibilities... So it looks like I'm gonna test out how far my D35 w/3.73 will take me with 33's.
So I am going to go a head with the spring lift, SYE & DS, MC CA and Track Bar, UCF TT, Lopro mount and engine skid. In the last month I've also picked up a front Currie Anti-Rock and Novak cable shifter. I ordered a set of brown dog 1" MML. I ordered it 2+ weeks ago and had not heard a thing, so I sent an email last Wednesday for an update and they said it would ship in 12-48 hours but I have yet to hear anything back... Good thing they are advertised as the last MM you'll ever need.
I also ordered a front bumper from Barnes4wd.com and will finish and install that and the anti-rock ASAP.
I am hoping to get the new springs, TB, ZJ TR, MC CA's and MML (if it gets here) this next Saturday. Especially since my wife isn't liking my parts pile and I gotta keep her happy if I want to keep the upgrades going
It will be a month or two before I can do the SYE and DS but as soon as those are in I'll be putting on the UCF Ultra High Clearance T-Case Skid and engine skid.
|01-01-2014 07:35 AM|
|BrutusTheTJ01||Hah I use 5th a lot..when I manage to get over 40mph|
|01-01-2014 05:59 AM|
|Neal5280||I'll just be happy to be able to use 5th gear again|
|01-01-2014 05:23 AM|
|BrutusTheTJ01||I think you'll be fine with the gears. I've heard that he 4.88s on 33s aren't a bad combo, your RPMs might be a little higher at highway speeds, but nothing terribly bad.|
|01-01-2014 04:53 AM|
|01-01-2014 03:56 AM|
|BrutusTheTJ01||I would go 2, 1,3.|
|12-30-2013 10:51 PM|
Order of Mods...
Ok I am getting a little bit of a headache trying to figure out the order of my upgrades for 2014. Everything will be done by the middle of July so want to try to do this in the most logical way possible. I wish I could do everything at once but for me it isn't possible. Please let me know which order you'd go an why...
1. Springs, SYE, Rear Upper Control Arms, TT and Front Trackbar. (Done by a buddy and I)
2. 8.8 & Front Regear to 4.88 (Done at a shop)
3. 35" MT/Rs
Current Set Up:
02 TJ - 4.0l, 5 speed, 3.73 gearing
MC Front Fenders
3" Front BDS 2" Rear BDS Springs
MC Rear Upper CA & Trackbar
UCF Ultra High Clearance T-Case Skid
|12-13-2013 12:33 AM|
|BrutusTheTJ01||Yeah they probably will, but hey more reason to get 35s.|
|12-12-2013 10:11 PM|
|Neal5280||Looking at your sig we'll be running a very similar set up. I have 33" Duratracs, 5100 and MC CA. I have a feeling when the lift and TT go on the 33s will look small. Hope to be rolling 35s before summer.|
|This thread has more than 30 replies. Click here to review the whole thread.|