Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > 4.2 carb options? Opinions welcome.

Join Wrangler Forum Today


Thread: 4.2 carb options? Opinions welcome. Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-28-2013 02:18 AM
indirocz28 The MR gasket plate does not cover the base of the carb, but your rebuild kit should come with a base gasket to go under the carb. It will be carb, base gasket (about 1/8" thick)
Plate gasket, plate, gasket, intake manifold.

The screws that hold the plate to the manifold are hex head Allen key, don't look like they will screw down in but they will.
Then the 4 nuts slide up into the bottom of the plate then the bolts screw in from the top.

They are not long enough to mount a throttle cable bracket or spring bracket though.

Mpg wise, right now 14mpg @ 80mph on the highway.
13mpg in town.

I have #50 jets, and have not fine tuned the idle mixture screws yet.
I am waiting for the CRT distributor. Then I will fine tune timing and vacuum and idle mixture.
06-27-2013 09:46 PM
Cashcrazy
Quote:
Originally Posted by indirocz28 View Post
If it is a 1.08 then it is. Lol

My 1.08 has #50 jets but fuel mileage might go up if I had in some 46 jets.
What are you getting MPG with your current setup? Did you have any problems with the MR. Gasket adapter not covering the base of the carb properly and causing a vacuum leak? I have read about several people having this problem.
06-27-2013 07:49 PM
Cashcrazy I have my carb all tore apart on the kitchen table and have soaked the big parts. I ordered the rebuild kit, adapter, and new float today from Advance Auto. No one stocks carb jets anywhere so ill have to order that online. I was shocked. I had #47 Jets in it, but one was stripped and chewed up. I am a perfectionist so I had to remove it. I am not sure if I want to go back with 47's or maybe go with a 46's.
06-27-2013 05:53 PM
indirocz28 If it is a 1.08 then it is. Lol

My 1.08 has #50 jets but fuel mileage might go up if I had in some 46 jets.
06-25-2013 10:47 AM
Cashcrazy I purchased as a 1.08 so I hope it is. All the info i could find said AMC only used the 1.08 on the 304. Someone can correct me if I am wrong. What do you know about jet sizes on the different venturi sizes. I had planned to use a #46 jet.
06-25-2013 10:35 AM
indirocz28 with a 304 huh? You're sure it is a 1.08?

Check your jet sizes when you take it apart.
06-25-2013 10:26 AM
Cashcrazy
Quote:
Originally Posted by indirocz28 View Post
I went through this same debacle. I ended up getting the $25 kit. The $50 kit was actually for a completely different carburetor. Oreilly ordered me this one to begin with, and I had to take it back and wait a for them to get in the right one.

This is where YOU need to find your part numbers on what you want. It appears that the day of a good parts store man is far past and now mostly filled with idiots.
The tag is long gone, but I do know the carb was from a 78 CJ7 with a 304. I am glad I can buy the cheaper part for once. My wife was complaining last night that she had to wait for me to go in three parts stores to get the right part. I told her the good days were gone where you told the man at the counter what you need and they bring back the right part.
06-25-2013 09:16 AM
indirocz28
Quote:
Originally Posted by Cashcrazy View Post
Have any of you found a MC2100 rebuild write up that was good. Most auto part stores carry two rebuild kits. One around $25 and another for about $50. What's the difference in the kits?

I went through this same debacle. I ended up getting the $25 kit. The $50 kit was actually for a completely different carburetor. Oreilly ordered me this one to begin with, and I had to take it back and wait a for them to get in the right one.

This is where YOU need to find your part numbers on what you want. It appears that the day of a good parts store man is far past and now mostly filled with idiots.
06-25-2013 09:11 AM
indirocz28 Here is a link to a PDF for the re-build:
http://www.therangerstation.com/tech..._2150_carb.pdf

Write up for the install: http://files.meetup.com/633539/Insta...%20a%20258.pdf


Yes the one pictured is a 2150, looks near identical to mine!
06-25-2013 09:09 AM
Cashcrazy Thanks for the help. I really appreciate it
06-25-2013 08:47 AM
89Saharagreen Leaks not links

Sorry
06-25-2013 08:18 AM
anotheridiot most the sludge just keeps filling the jets. its also likely your vacuum solenoids are bad and not triggering your idle solenoid to raise the rpms on the slow down. We just put too much in fixing the emissions to give up and get the two vacuum tube carb. Its a real simple carb to rebuild and I just got solenoids from an industrial supply to replace the two bad ones.
06-25-2013 07:46 AM
89Saharagreen Cashcrazy

Look on the side of the carb there should be a raized cast mark about the size of a nickel with some numbers on it match the numbers on the cast mark to the list of numbers I posted earlier and you will know your CFM. As far as parts kit or rebuild kit I used the Autozone one because they are closer than Advanced to me only reason but it cost about 30 dollars did everything I needed it too.

The hard line coming out of the back of your carb picture is for the PCV if you did not know that. Becareful with all the small parts if you have not rebuilt a carb before they can get lost easily I used a white towel under my carb makes dirty parts stand out.

Lastly when you do your function test look for links around the Throttle Shaft assembly
06-24-2013 10:35 PM
Cashcrazy Have any of you found a MC2100 rebuild write up that was good. Most auto part stores carry two rebuild kits. One around $25 and another for about $50. What's the difference in the kits?
06-24-2013 04:51 PM
88Sahara
Quote:
Originally Posted by Cashcrazy View Post
I think 88Sahara meant to put 1.08. I ordered a 2150 and look forward to having a jeep that won't die at stop signs.
Yep. Sorry. Carn'td tieyp
06-24-2013 02:37 PM
Billmummey Looks like one.... Should have a cast mark 1.08 on the side
06-24-2013 01:24 PM
Cashcrazy Thanks for the response. Can anyone verify this is a 2150?

06-24-2013 12:12 PM
89Saharagreen
Number = CFM
.98 = 190
1.01 = 240
1.02 = 245
1.08 = 287
1.14 = 300
1.21 = 351
1.23 = 356
1.33 = 424
Created
06-24-2013 12:11 PM
89Saharagreen
CARB 2150 Question

I literally just finished installing my 2150 on Friday. The jeep runs great with this carb. The carter carb is a hit or miss even when rebuilt the idle tubes are prone to clogging even if you drill them out in my opinion.

The motorcraft runs strong you want the 1.08 venturi if you can get it.
If your buying from the Carbguy he knows what you need.

I happen to have access to a 1.21 venturi for a very good price gives me 350CFM which is way more than you need in my opinion again, the Throttle assempbly arm was bad but only cost me 19.00$

make sure you connect up your PCV to the carb in the back near the throttle linkage if you can if not use the Brake Booster connection and run a brass tee of the intake manifold needs to be 3/8 hose or larger.

Go ahead and change all your vacum lines that you plan to keep at this time unless they are new mine were trash which is part of the reason the carter ran like crap.

After the install it purrs like a kitten.


Biggest pain in the butt was figuring out the throttle linkage and springs you will need to do some fab work very minor I used existing parts from my carter swap out.

Good luck you will love the results

Oh btw use good gasket sealer on all gaskets and get the thick gasket helps with moving the linkage arm up enough to clear the brake booster tee.

Chief
06-24-2013 08:25 AM
Cashcrazy I think 88Sahara meant to put 1.08. I ordered a 2150 and look forward to having a jeep that won't die at stop signs.
06-24-2013 08:07 AM
busemans i thought it was 1.08?
06-24-2013 06:10 AM
88Sahara Motorcraft 2100 or 2150. You'll look for the one with the 1.18 venturis and has that number cast into the side.
06-24-2013 05:53 AM
busemans i have a 4 barrel holley. a 450cfm
06-22-2013 10:37 PM
BCDonny I am so happy with my motorcaft 2150 on my 4.2 would also recommend the HEI dizzy
06-22-2013 05:47 PM
Cryptids I have the motorcraft 2150 on my jeep yj 4.2 installed by the Colorado Springs dude who specializes in them. It works well for me and is fairly easy to tinker with. Has a tricky time warming up though so I gotta check that out.
06-22-2013 04:42 PM
87YJnTX get rid of the carter.........best option.
06-22-2013 04:33 PM
Cashcrazy I should add that I am thinking about swapping carbs because the Carter BBD was rebuilt in 2012. I think that is a record for me on a rebuild. Historically, I have always had years of service from a single rebuild.
06-22-2013 04:20 PM
Cashcrazy
4.2 carb options? Opinions welcome.

89 Yj/4.2/auto. My Carter BBD decided to crap out me. Now I am getting the dieing at red lights and running like a model T that was pulled out of a barn. It ran ok for about two days after aggressively spraying it with carb cleaner. I have been looking all over for a 2150 and located one about two hours one way from me. The non-electronic Carter's are easier to find and people aren't pricing them like they are gold plated. Will a rebuilt non-electronic Carter be a direct bolt on and give much more dependable service than the electronic version? I just spent about $500 on parts and really need to keep the cost down, but at the same time I am tired of it running horrible and dont want to have this happen again in six months. Has anyone ever switched to the non-electronic Carter and had long-term dependable service? I want reliability over upgrades that are just for performance.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:53 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC