Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > wiring harness thru firewall?

Join Wrangler Forum Today


Thread: wiring harness thru firewall? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-26-2013 12:00 PM
okcscott Thanks to both derf & BManz. The boss's jeep has a RockHard roll cage so no plastic panel just plate steel, no clips to break! She has been trying to decide how to cover or paint that open place. That should be fine to pull my wires. save me lots of work. Thanks for the quick reply.

06-26-2013 11:01 AM
BManz I had to wire up some strobes and used an access hole filled with foam. I believe these are on both sides, and here is a pic of the passenger that I used as it's closer to the battery (I wanted a hard connection). It comes out along the edge of the hood. I recommend running a coat hanger from the engine-side and poke it through; it's very lightweight foam.

06-26-2013 10:43 AM
derf There's a hole with some insulation you can push through. I don't have my camera handy but I'll try to explain.

If you open the passenger side door you can see on the side of the dash there is a panel that is right up against the door when it closes. If you carefully wedge a knife in the seam you can pry it out. It's plastic and easy to damage so take your time and be careful you can avoid damaging it. Once you get the first couple of clips to pop loose you can get a finger in there and pull the panel off. It's only clips, no screws.

Once you have that open you can see on the firewall a hole in the aluminum bracket maybe 1/2 to 3/4 of an inch in diameter. It will be filled with what looks like expanding foam insulation.

You can straighten up a coat hanger and push it through the insulation.

With the hood open you will be able to see the end of the coat hanger pushed through. Tie your wire to the coat hanger and pull it through. It's a good idea to protect the wire as it routes into the engine compartment to keep it from wearing a hole in the insulation. But that's not too terribly hard to figure out.

I can probably take pictures later in the day.
06-26-2013 10:14 AM
okcscott
wiring harness thru firewall?

Made several small wiring harnesses, (12v aux, power locks, and power for alarm) Is there any place to pull thru the firewall on the pass side without drilling a hole? I did see a large rubber boot with a wiring harness pulled thru with both sides taped?? Thanks also photos might help. Trying to do this right

[/URL]

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 04:50 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC