|06-30-2013 04:50 PM|
|OverkillYJ||This is the part you need.|
|06-29-2013 08:29 PM|
|06-29-2013 08:26 PM|
|Mowrangler||harleydragon sounds like you and I are in similsr situations I am going to put this thing back together and see what I have. The only difference is my po was an idiot and couldnt put in a driveshaft correctly. This YJ will see some mud puddles ,some sand and a few slippery boat ramps no extreme use and very little high speed use.Heck I dont put 5K a year on my daily driver. Thanks for your help.|
|06-29-2013 08:19 PM|
Thanks Overkill that is just about what I estamate where I will be. Next step is to replace damaged yoke and output shaft then mesure and have driveshaft legthened.
I have located a yoke but I still need a tc output shaft. Thanks everyone for your input I have been working on cars for 42 years but this is not an area that I work on often . Thanks
|06-29-2013 08:14 PM|
|harleydragon||my yj is soa with stock driveshaft and no vibration.transfer case is dropped 1 1/4 inches.I would like for the driveshaft to be about an inch longer but it does not get extreme 4 wheeling..I have put about 10,000 miles on it in the last year with no problems|
|06-29-2013 08:05 PM|
|06-29-2013 07:58 PM|
|Mowrangler||Overkill my Transfer case has been dropprd about 1.75" and the driveshaft angles look near stock as compared to a friends YJ I just looked at. His has not been lifted or modified my driveshaft couldnt be more than a degree or so different. Once I replace the yoke and the output shafr I will probably have to have the shaft lengthened ahout 1.5-2.0 inches to insure proper travel.|
|06-29-2013 06:41 PM|
|OverkillYJ||I know Ibuildembig does not use SYE kits. 99% of everyone else does. It reduces the angle. Less angle = less stress. Stress causes failures. I also think he usually drops the TC an inch or two. You would have to ask him though.|
|06-29-2013 06:05 PM|
|Mowrangler||Yes ALLMUD that is correct, After i do that I will see if there is any other problems.I any one has these please Pm me with a price shipped to 33611 Thanks|
|06-29-2013 05:55 PM|
|AllMudd||Mowrangler- you need the rear yoke for the dana 35? And the output shaft for the TC?|
|06-29-2013 05:49 PM|
|Mowrangler||I will bet the failure was due to improper installation of the rear u-joint in the yoke, the cups were still in the yoke but the rest of the joint and shaft were mia.One cup was in its proper place but the other was on the lip, both the cups ,ubolts and the yoke were badly mangled. I dont know if I will have bad vibes till I fix the problems I know I have.There is another member of this forum who has a sticky on soa's who says he has done a ton of them and has never had to go with a sye or a CV shaft.I will say that I would like to see the driveshaft to be about 1.5" longer to make the seal ride in its normal place on the yoke but that is all I think I MAY need. What bI doo need now is a replacement yoke for the rear and a replacement output shaft for the t-case. Cheap?|
|06-29-2013 05:18 PM|
If they were running stock shafts I would bet anything the horrible angles caused the ujoints to fail, and it probably vibrated like a giant dildo rolling down the road.
|06-29-2013 04:46 PM|
|Mowrangler||Apparently the PO didnt get the rear u-joint in the saddle correctly with one cup on the tab and oner inside the tab so when the driveshaft let loose it damaged the rear yoke and bent the rear output shaft slightly ruining the extension housing. I mocked it up w/o the housing and the shaft is the correct length and ujoint angles are near perfect.So now I need a new output shaft and a rear yoke. I really do not want to spend the money on a sye because this jeep will not see extreme off road use.|
|06-27-2013 08:51 PM|
|OverkillYJ||If you dont know Jeeps, you need to have someone who does go over it in detail. Or post a ton of pics of steering, springs, trans, TC, skid plate, basically everything. X2 on this sounding like an unfinished project. If you drive it after just throwing driveshafts in it that could be the end of you and the Jeep. I would at least expect you get driveshafts cut to cusomte lengths, need to change stuff to make it work and then need them re-cut.|
|06-27-2013 05:23 PM|
|Mowrangler||Cant post pics of the driveshafts they are mia,no apparent damage to the transfer case. just got replacement shafts today both front anf rear fit perfect and have plenty of travel.Will update after I get the thing on the road.|
|06-27-2013 07:35 AM|
I am going to go out on a limb and say they had stock drive shafts and blew them out on the trail because they did not do the slip yoke eliminator.
Can you post a pic of the shaft? and the rear tail housing we will know for sure from that.
Also look for any damage! If I am wrong and I hope I am then you may just need a custom rear drive shaft to get it on the road so to speak.
|06-27-2013 07:30 AM|
|06-26-2013 08:43 PM|
|06-26-2013 08:41 PM|
|06-26-2013 08:11 PM|
No doesnt have a SYE installed just a splined shaft sticking out of the transfer case.
I am not planning on a lot of serious suspension travel just some mud puddles. Just trying to get this thing somewhat functional.http://s450.photobucket.com/user/54G...38303122785265
|06-26-2013 07:54 PM|
I already answer him....WoW that made me sound like a jerk....lol
The stock front shaft will work just fine....
Hopefully you already have a SYE kit in stalled in the TC....that way you'll just need your local DS shop to make one up for you...
|06-26-2013 07:37 PM|
|AllMudd||Not sure on that one. I haven't honestly heard of many ppl that change it out. Maybe someone will chime in or go ahead and search SOA and ask someone that has SOA what the did. I have a 4" lift with stock driveshafts but most of the time ppl suggest the SYE for the transfer case.|
|06-26-2013 07:36 PM|
|06-26-2013 07:11 PM|
|Mowrangler||Looks like a trip to the driveshaft shop, will the front be OK?|
|06-26-2013 05:57 PM|
#1 No with spring over the axle you need custom rear drive shaft.
#2 slip goes closest the front axle.
|06-26-2013 04:46 PM|
Stupid Driveshaft Questions
i just recieved my 1995 YJ 2.5 5 speed it was a repo that I bought sight unseen. It was missing both drive shafts, it has stock springs , spring over axle and stock shackles.
#1 Will stock length driveshafts work?
#2 On the front shaft does the slip end go on the top (transfer case) or the bottom (Differential side)
Any input would be appreciated.