Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Water in my axle

Join Wrangler Forum Today


Thread: Water in my axle Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-01-2013 08:52 AM
TLATEOTW sometimes those seals are not bad enough to leak oil from the diff, but when water can still go in, i crossed a river yesterday , the water was high as about 3/4 of my 32 inch tires, i got watter in my diff althoughy seals don't leak, I'm gonna order outer tube seals very soon
07-01-2013 08:06 AM
Ole4Cyli This happened to me recently. Just pop off the diff cover and clean it all out the best you can. Don't worry about replacing the seals yet. Just put new cheap fluid in, and in a couple hundred miles change it again to flush it all out just to be safe. If you still leak after a week or two after you change your fluid the first time, then you probably have bad seals.
07-01-2013 07:56 AM
TLATEOTW i bet, you have bad inner seals, not a breather tube issue.
06-28-2013 01:59 PM
Texas2070 Mine breather is by the radiator. Lucky I've only got water in the diffs and transfer case. I just got done breaking open the t case and got all the water out. To much work for one day
06-28-2013 12:12 PM
NYJETS I have a manual.. My front breather was in the front left wheel well. The rear was in the right rear well. The tranny breather is at the fire wall in the engine bay. I relocated the front up into the engine bay next to the abs unit and the rear up into the right rear tail light space. It gave me 8 inches of more water clearance...
06-28-2013 09:58 AM
Jerry Bransford How could you have gone deeper than the front axle's breather tube opening unless you didn't have the factory remote vent tube connected to the axle housing? The front & rear axle remote breather tubes vent at about the level of the top of the radiator.
06-28-2013 08:39 AM
PStov98TJ
Quote:
Originally Posted by NYJETS View Post
If you are going through water you may want to extend those breathers. Thanks to Rooster 76 here I did it myself out of some fuel line, hose menders and some worm screws from my local auto parts store. Cost me $22 and about an hour of labor. I am by no means a Jeep mod expert but it was really easy. Now my lowest breather is the transfer case at 37".
What trans do you have?

And to the OP, you should do a fluid check in your t-case and trans as well because the breathers for those are far below the height of the front and rear diffs.

And just for reference, this is a diagram of a jeep with the AX-5 trans and np231 t-case. So the diff and t-case locations will be the same for all non-Rubicon TJ's, trans will differ however.
06-28-2013 07:31 AM
NYJETS If you are going through water you may want to extend those breathers. Thanks to Rooster 76 here I did it myself out of some fuel line, hose menders and some worm screws from my local auto parts store. Cost me $22 and about an hour of labor. I am by no means a Jeep mod expert but it was really easy. Now my lowest breather is the transfer case at 37".
06-28-2013 07:25 AM
Texas2070 Damn I didn't know brake cleaner got water off that well. The whole thing looks new. Thanks!
06-28-2013 07:19 AM
Rubicon06Va Use Brake Cleaner or WD-40 to propel water from diff. I wouldn't remove bolts from ring/pinion.
06-28-2013 07:03 AM
Texas2070
Water in my axle

The other day I was in the creek and got submerged below my front breather on my axle. Now there's water in it. I took the diff cove off to drain the oil but I want to put some paper towels in it to make sure I clean all the water out.

If I unscrew the 4 bolts that hold the ring and diff in can I just screw them back in when finished with out any problems? I'm just a little scared operating in there because I know there's alot of measurements and stuff and I don't want to do any harm.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:29 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC