Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Transfer Case Lowering

Join Wrangler Forum Today

Thread: Transfer Case Lowering Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-19-2006 12:29 PM
daddyjeep Nice explanation JeeperDon.
12-19-2006 11:28 AM
nuadu78 Cool

Thanks for the pics

12-19-2006 08:59 AM
Originally Posted by Odd is he View Post
I was just about to comment on how nice of condition that frames is for a YJ....
I worked hard on that! Then I realized I was in YJ chat.
12-19-2006 06:37 AM
Odd is he
Originally Posted by Simple Scout View Post
I just realized I should have metioned that these pics are of a TJ.
I was just about to comment on how nice of condition that frames is for a YJ....
12-18-2006 10:47 PM
Scout I just realized I should have metioned that these pics are of a TJ.
12-18-2006 10:43 PM
Scout Here's a few quick pics from the drivers side of my Jeep. (It won't be on here much longer)

Side shot:

From rear tire looking toward front tire:

From front tire looking toward rear tire
12-18-2006 09:56 PM
nuadu78 alright, thanks for the feedback from all of you.
That will help me big time.

12-18-2006 06:41 PM
Originally Posted by nuadu78 View Post
I mean, I know what I need to lower that thing
Lowering a t-case is to fix a specific angle problem. You do not know if you will have the problem or not.

When a smooth output of a t-case goes through a u-joint bend, the momentary speed of the drive shaft (degrees of rotation/time) varies, meaning the drive shaft goes slightly faster and slower during each part of a revolution. A correspondingly equal bend as the drive shaft attaches to the axle pinion perfectly compensates and the pinion spins as smoothly as the t-case shaft. If the bends are not equal, that speed difference shows up as a vibration.

After a lift, the drive shaft bend at the t-case and at the axle should be exactly the same, meaning the output shaft of the t-case and the input of the axle are parallel (not on the same line, just parallel), it should be fine with a 3" lift. If the lift gets tool tall (the parallel lines get further apart), the bend angles of the drive shaft, although still providing a smooth ride, start to cause a short life spans on the u-joints.

Lowering the t-case (tipping it down), and a corresponding altering of the axle pinion angle (tipping it up) to keep the lines parallel, simply makes the two parallel lines close together so the u-joints last longer. In most cases, 'vibes' are due to mismatched angles. A t-case kit can reduce the mismatch and eliminate a good part of the vibe, but at the cost of reducing clearance. Altering the pinion angle is a better way to fix the vibes as it keeps good clearance.

Do your lift. Keep the lines parallel, and you should have no problem with only 3 inches.
12-18-2006 06:26 PM
whiteyj Lift kits like the 2-1/2" RE, have 6 pucks that are 1" thick. You loosen the skid plate bolts and drop one side then the other. Kit includes new longer bolts and fresh flat washers.
12-18-2006 03:42 PM
chasm Just put 3" lift springs and new shocks, etc. on my 93 YJ. Didn't do an x-fer case drop yet. I want to see how it rides after the new leaf springs settle in a little bit. Initially, I had some drive line vibes from the rear pinion angle being a little to sharp. 2.5 degree shims added to the rear springs solved the problem with the vibrations.

I don't want to drop the x-fer case unless I have to. It kind of defeats the purpose of lifting the Jeep if you're going to make its' belly lower.

Just my 2 cents!
12-18-2006 03:30 PM
18derrick A Tcase lowering kit is just two bars of square tube that bolt between the skid plate and the frame. The skid plate is in the middle under the jeep and the tcase is bolted to that. you just remove one side at a time and slip those in. very easy. Although with that much lift I dont think you need one.
12-18-2006 02:07 PM
Transfer Case Lowering

Fist of all Hello.

This is my first ad in this forum and I am looking forward of some intersting talks.

Alright, I am planning to intall a 3 inch lift kit on my 94 Wrangler,
the only problem I have is that I don't know how to lower the transfer case.
I mean, I know what I need to lower that thing, but I just don't know how it will look like or how it works.
Does anyone has a good link where I can see it ??
Or even a picture would work out.
If anyone has a picture, than you can send it to

thanks in advance


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 12:29 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC