|07-01-2013 04:12 PM|
The most important thing with adding leafs or rebuilding them is to make sure you get the little plastic slips in there. You also do not want to restrict their movement. Those little slips are what let the metal leaves slide against each other without stopping. Without them the springs will bind up easier, and also ride stiffer. Same happens if you clamp it too much or too tight. So if you cut and make your own, just make sure you drill them and make them exactly like if you bought a leaf.
Doesnt matter to me anyways though, no matter how I did it I would have bent that leaf. Fortunately it was only one and not two.
As far as the rubicon leafs, they will give you 1"-2" of lift when added. A good shop could make them stock height with the extra leaf if you wanted though.
|07-01-2013 03:30 PM|
|07-01-2013 02:32 PM|
I didnt use an add a leaf. Overkill did.
Im running a set of stock rear yj packs up front. I took another set of main leafs and cut right at the eyes and those are under my main leafs. Then I used spring clamps on both ends to clamp the 2 leaves together.
My springs set up this way gave me just abiut a half inch over my 4.5 re sua springs I had before.
I drive almost exclusivly on rocks and I have had no issues so far.
There is a shop in sac that I called. Hanleys blacksmith I think it was. I think it was a couple hundred bucks. Idecided to just try my cheap approach and havnt regretted it yet.
Mbclark are you on the norcaljeepers.co board? Most of us are in sac but I dont recognize your rig
|07-01-2013 02:25 PM|
|07-01-2013 01:27 PM|
Yj leaves are short. Some dodges use an upsidedown eye like that but they are long. I would get another main amd have a spring shop do a military wrap on them. Thats gonna be the best way to keep from bending them
The only thing the upside down eye does is give less lift my a small amount
A spring clamp on the main and that add a leaf may have prevented that as well. I use the bend over tab ones and I drive like a blind man sometimes and my springs are holding up great.
|07-01-2013 12:27 PM|
|07-01-2013 11:44 AM|
|Ibuildembig||I understand, I dunno of anything that uses the same stuff as a Yj.|
|07-01-2013 11:39 AM|
|OverkillYJ||Did that last time I hit something. Too much money for the work. If I was going to spend that I would just buy new springs.|
|07-01-2013 11:22 AM|
|cakes567||Take em to a spring shop.|
|07-01-2013 10:57 AM|
|OverkillYJ||The only thing I like about those is that when they flex all the way they do not bend backwards as far. Seems it would be less stressful on the springs. My regular ones have lasted fine since I did them about a year ago. I just figure if I could pull that style off something for $50 at a yard I would give them a shot. Especially since I need to pull these apart anyway at this point.|
|07-01-2013 10:36 AM|
|Ibuildembig||Nothing factory is made that way that I have ever seen. I don't see where they get off calling them soa specific since every 4x4 truck made has the springs on top and they aren't wound that way.|
|07-01-2013 09:39 AM|
Main leaf for SOA
So does anyone know where I can get the Rubicon style main leaf? Is there another vehicle I could pull that style off that would fit my YJ spring pack up front. If you notice I already have the Rubicon full length add a leaf added to my springs. I damaged my main spring after hitting a stump covered in mud on Saturday. I could get a stock set of springs from someone for cheap and replace the main leaf from those, but I would rather get the other style since they are designed specifically for spring over applications. I would like to stay around the same height, but if I gained an inch that would be ok too. If there was a way for me to do this front and back that would be nice too. I am not going to buy the Rubicon SOA leafs, and if it end up being nothing will fit I will just have to replace it with what I already had in there. They flexed awesome.