Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > possible starter problem

Join Wrangler Forum Today


Thread: possible starter problem Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-16-2011 06:26 PM
ACK4wD I have a similar problem - 97 TJ Sport 5 speed 4.0 - engine starts as the weather gets cooler it starts to get finicky - If it siuts for a while and I charge up the battery up it will start. It will run a while and then may not start. With the clutch in and I turn the key it makes a loud click but the starter doesnt whirrr. If I push start it and the Tj sits in idle I can turn the ignition and the starter engages (so I know it's working.) I has a new battery - the voltage is near 14 - the amperage is solid too. I do notice that when I turn the key that it is drawing nearly all of the juice from the battery - the clock dims significantly. Two places have tested the battery and alternator - they seem to work. question: solenoid? Ignition switch? this problem seems to come and go so it's hard to take it to someone and have it work when they see it and say it's broken..
10-18-2005 12:53 AM
willness33 A little late but here's my take. Clean your battery terminals. Make sure the starter lead is good and tight. Charge the battery overnight. Try it out. A couple things to comment on also. Using your charger on the start engine option will not give enough cranking amps go wrench the starter out of your hands, like it should on a fully charged battery. This may be a stretch but bear with me. When you try to start the jeep, and all you hear is a click, the starter is engaging, but may not have enough amperage to turn the engine. You will still have 12 volts with no load, but not the amperage required. Your troubles may very well be dirty terminals, poor ground, poor connection on the starter or most likely a dead battery.
10-15-2005 05:18 PM
jeepmutt Another thought... is your buddy sure about the 12V at the starter? If you have a bad lead preventing the full 12V, but out of the Jeep on the bench there was a good connection, that could explain why it works on the bench and not in the vehicle.
10-15-2005 05:12 PM
jeepmutt I still think it could be the solenoid. I doubt it's a matter of teeth not matching. Almost certainly something would touch the ring gear little bit and you'd get a grinding of some sort or at the minimum hear a whirring of the starter instead of just a solenoid click. Also be sure you have good ground.
10-14-2005 04:14 PM
4Jeepn Well I was going to say check the solenoid but it sounds like you did that. go get another starter and see what happens, also I can't recall but I think when I put my new one on I had to make sure it matched up with the Flywheel teeth, but I could be thinking of when I did it on my CJ.. too many jeeps to many parts..LOL
10-14-2005 03:28 PM
kelly
possible starter problem

folks, i have a 02 wrangler 4.0........i think i need a new starter..due to it going click.........click...etc when i turn the key. O'Reillys tested it and said i need a new one. i bought a rebuild for 74.00 and put it on. same symptoms as prior to the purchase. my buddy checked with a meter and i'm getting 12v at the starter.......is it possible that i got a bad rebuild? one thing more, this morning i tried to tighten the nut on my starter cable on the starter and i (of course you idiot!) got an arc because i didn't disconnect the battery.immediately after is when i started getting the clicking sound....I don't know what else to do..................we also hooked the starter in question up to my charger on "engine start" the solenoid engaged and the gear spun but didn't seem like it was going quite strong enough. is it possible that i messed something else up or just bad luck with a rebuild?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 10:21 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC