|12-09-2014 09:56 PM|
Ok so I figured my issue out. The one headrest I did not fully push one of the spring ends off the head rest post. So make sure all 4 spring ends are totally free of the posts and not hanging on them at all. Make sure they are 100% free and clear.
Once I did that they stay down all the way and are perfect.
|12-09-2014 03:45 PM|
|12-01-2014 07:27 PM|
|Wingnut3140||I followed the steps and they stayed down for a minute. Backing out of the driveway they popped back up. It's a simple spring removable so I didn't miss a step. Anyone else have this issue?|
|10-15-2014 12:16 AM|
|BareBones13||Just did this on my '15 JKU and it took about 20 minutes. I did have to unhook both sides of the spring as I could tell the head rests wanted to pop back up when only 1 side was done. I added zip ties, although I'm not sure that I would really ever need them.|
|09-27-2014 08:55 PM|
|BobnPaty||Check out the video at https://www.youtube.com/watch?v=vC5m...ature=youtu.be It shows you how to attach a zip tie to recover the spring later if need be. I haven't done the mod yet because most of my tools are 1,00 miles away and the cheap needle nose pliers I have here can't seem to keep a hold on the spring while I slide in a zip tie. I do wonder how well it will work anyway though. What would keep the zip tie from slipping off the open end of the spring? I'll be heading back home in a few weeks and will try to answer the question then. I'll post a comment if I can figure it out.|
|09-01-2014 08:20 PM|
Two flathead screwdrivers did the trick. Thanks for the instructional.
Decent visibility has now been achieved.
|09-01-2014 10:54 AM|
|Maximum Carnage||Knew I'd see this somewhere, going from car seat to booster seat you need this.|
|08-18-2014 05:08 AM|
Very cool. Did both Jeeps, the vision is great and still have functional headrests. One tip I would give is once you get the spring unclipped, use a flat blade screwdriver and push the spring assemble away from the arm.
Great stuff and thanks for the writeup!
|05-31-2014 01:08 PM|
|mouse357mag||THANKS! This may just be the most useful thing I have heard on here (besides tightening 2 bolts to keep the back door from popping) since the bungee cords didnt really work. Although I did have to remove both of the springs off of each headrest|
|05-30-2014 10:36 PM|
|05-30-2014 10:11 PM|
|ibrown3005||You should be able to fold the seat back down. When you put the seat back in the upright position, the headrest should stay down.|
|05-30-2014 09:23 PM|
Ok so I have had my rear headrest down (pulled springs) for about 4 months now.
When I went to put the soft top on I hit one if the headrest and now it's stuck in the up position. I don't see the springs anymore, how do I get it down again ...... Please help! I hate when they are up.
|04-17-2014 10:28 AM|
|jrenewill||Just did this easily in 5-10 minutes using two flathead screw drivers. You guys rock! I knew there had to be some way to get those headrests to go down and stay down. So pumped! Now ready to do some more mods.|
|04-07-2014 09:03 PM|
|04-07-2014 05:18 PM|
For a slightly less permanent version I just grabbed a couple of 18" bungie cords and used them to hold the headrests down.
I found they were the perfect length and you can affix them from the headrest to the tie down points on the bottom rear of the seats in the cargo area.
|04-07-2014 12:04 PM|
I did this mod this last weekend. Only issue I have is there is still enough spring tension that a good bump in the road or a speed bump and the headrests "pop" back up into the up position.
I may have to try and release the other end of the spring to stop this...
|03-26-2014 12:13 AM|
|KTMtahoe||Wow, thanks, just did this, soooo much better, my wife is stoked, it really help the visibility. Needle nose didn't help, not enough to grab, our jeep is only a few day old so perhaps the springs hadn't loosened up. Took two screw drivers, one to pry then stick the other under to move aside. The second seat we both did it, one to hold the seat while sitting in the other seat to access, if that makes any sense at all. Anyway, THANKS.|
|02-15-2014 02:50 PM|
I found it easiest to just push the spring off the post with a flathead screwdriver. (Needle nose pliers couldn't quite do the job for me.) The spring has a tendency to hang partially unhooked, so be sure to shove it completely free of the post. (It can still provide tension if you don't.)
I tried removing just one spring per headrest at first, but there was still enough tension to pull the headrest back up. So it was necessary to remove them both. The springs on the inside posts of the headrests are harder to see and you have to either get into to rear compartment or slide onto the middle of the black seat to get the best look.
I love the more open view out the rear now...this really helps. Just be sure to push the headrests back up when you have riders in the back seat.
|02-02-2014 11:31 PM|
|phansson||Just did this mod, it took about 10 mins and will definitely make driving my Jeep a better experience. You just can't see out of the back with the spare tire and those headrests!|
|01-18-2014 05:58 PM|
|New2012JEEP||Maybe the spring got caught up once tension was removed, open her up|
|01-18-2014 03:43 PM|
Question: one of my backseat headrests has been locked up and no matter what I try I will not release.
Has made it impossible to put rear seat down due to front seat passenger not wanting to rest chin on dashboard.
I performed the spring sliding mod mentioned by op but still locked up.
Any help would be greatly appreciated.
|01-18-2014 11:10 AM|
|JeepKenn||Thanks, OP!! Did it this morning to a 2014 JKU and its works great.|
|12-29-2013 01:23 PM|
just did it with a medium habor freight brand flathead screwdriver, took about maybe 20 mins max and it did the job !!!
To the threadstarter Thanks for figuring this mod out, easy and got those pesky headrests out of the way !!
|12-29-2013 12:08 PM|
I cant think of what vehicles i rode or driven in as of lately, but im quite certain some of them didnt have headrests for the back seats. i think its a safety standard for newer vehicles though.
oh well onto the spring removal today.
|12-29-2013 02:34 AM|
|Lusus_Naturae||^ It's kinda nice this way though, I would hate to have to store them somewhere if I needed them. Having them hang off the back hasn't gotten in the way at all.|
|12-28-2013 12:34 PM|
|donmeca2020||nice find, i might just try this today !!! sucks Jeep didn't make our backseat like the 3 door models with ease of just popping out... oh well on to this mod.|
|11-22-2013 04:10 PM|
|11-21-2013 07:07 PM|
|Flatlander21||Yep. Worked on my 2014 JKU.|
|11-21-2013 12:21 PM|
|4JeepNfun||Has anybody tried this on a 2014 JKUR yet?|
|11-18-2013 03:15 PM|
Did this mod just now. Crawled into the cargo area of the JKU, peered at it for about 5 minutes, trying to figure out how I could use the needle nose to help. Turns out my ~12" flathead driver worked like a charm. Work from the outside of each spring, pushing the end of the spring toward the back of the vehicle. Takes a lot of pressure... I also suggest wearing protective eyewear, so you don't slip and lose an eye.
Rear seat headrests folded back when not in use, easy to put up or keep down... mission accomplished!
|This thread has more than 30 replies. Click here to review the whole thread.|