Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Clutch Slave Pin - Broken in half?

Join Wrangler Forum Today


Thread: Clutch Slave Pin - Broken in half? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-10-2013 08:42 PM
jokerchief462 Clean the threads. They are wet holes on some so a little RYV on them reinstall good to go.
07-10-2013 08:40 PM
Rob_Feature Thanks guys. I took the plate off and did my best to clear out the pin hole, then put in the new pin, bumping it down a bit with a rubber mallet. Seems snug enough now.

My only question was about taking the plate off...when I did, the plate bolts had a green film on them...should I be adding some sort of compound to these when I put them back in? Also any ideas how tight they should be?

Thanks!
07-10-2013 07:16 PM
jokerchief462 It is a front cover and that is all. Easy enough to remove. You should be able to clear the old pin and install the new one and replace the cover. May be a good time to put in a new desk while it is apart. The pin maintains alignment if the slave cylinder.
07-10-2013 05:41 PM
AllMudd Kinda confused on what pin and hole you are referring to. But that big plate allows you to see some of the gears and synchros. And it's removable for rebuilds and replacing the shaft seal.
07-10-2013 03:25 PM
Rob_Feature
Clutch Slave Pin - Broken in half?

I'm replacing my slave cylinder and, when I opened up the trans to get to it, I found the pin and retaining nut were in pieces inside the bell housing.

Since the old pin piece I found is shorter than the new one that came with the clutch kit I'm suspecting that a small piece of the old pin is broken off inside the pin hole. I have no idea how to get it out?!

I put in the new pin and it feels like it doesn't go in as far as it should (but I have no frame of reference).

Thoughts on what I should do? Should I assume the broken pin is still in there and not proceed until I get something out? (suggestions on how?) Should I ignore it, put in the pin in anyway and assume it'll stay put? (thinking not).

Any ideas?

The other option I suppose is to remove the big plate with the big bolts that the hole is actually in and hpoe I can push the pin out from the other side. But, I dont know what that plate is and what I may be getting into if I remove it.

Help! Thanks!

Here's a pic of the 'big plate' I refer to above (thanks to another JeepForum poster for this pic):

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:03 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC